Hey, I finally joined the club. I've been waiting for too long. Does anyone make a teal colored cabinet leg protector? if not, what color cabinet protector should I purchase? I was thinking just black may look nice.
You're currently viewing posts by Pinsider wombat.
Click here to go back to viewing the entire thread.
Hey, I finally joined the club. I've been waiting for too long. Does anyone make a teal colored cabinet leg protector? if not, what color cabinet protector should I purchase? I was thinking just black may look nice.
Quoted from Coyote:Interesting - I never knew that existed. Never have seen it on a game. Good find! Anyone have one on theirs?
Does anyone sell the bracket assembly?
I need some help with identifying the parts in the picture. These pieces were missing when I finally grabbed a WCS94. The blue arrows represent the black spacers. What length and diameter are these? The red arrows point to the plastic washers. What diameter are these? The yellow arrows are pointing to the screws that hold everything down. What type of screws are these and what length? I've also noticed this same setup on the other ramp entrance. I understand that this plastic washer setup is protecting the ramp entrance. Was this stock or something that came later? Thank you in advance for the info. This has been driving me batsh*t.
pinside2 (resized).jpgQuoted from Davi:The previous owner is almost right. There is only one clear post (type 03-8319-**), based on parts list.
I think here (clear star post is part of A-18775 striker brd assy):On top of that you need:
20 pcs 03-8365-25 post #8 trp-teal grn
5 pcs 03-8044-13 post mini-clear
2 pcs 03-8247-13 post #8 double star-clear
2 pcs 03-8247-25 post-#8 double star trp-teal
2 pcs 03-8130-13 post double star-clear
I have a clear post next to the shooter (next to the ball eject) Is this the same on every WCS94, or just mine?
Please, could someone that has an original topper please take some pictures of the hardware used to mount it. I'd like to keep things original if possible. Thank you in advance.
Need help with wiring please. I've recently reinstalled the backbox and now having problems with 3 connectors. The connectors are keyed but doesn't help in this situation. J116, J117, and J118 are the board designations I'm having problems with. The picture below will hopefully help. One connector is part of the DMD cable set. One connector is part of the cable set that connects to J119 (purple - white/purple). The third cable is coming out of the vinyl tubing by itself. Please help. I only need 2 out the 3 to figure this out.
wiring problem (resized).jpgQuoted from Archon9000:This should help
[quoted image]
Thanks for the input Archon - must appreciated! It appears that J116 and J118 are basically interchangeable. It wont hurt any electronics if those are switched. One is for the playfield and the other is for the cabinet. Is, "cabinet" (J118) referring to the backbox?
Do the 3 stadium lights just stay on all of the time, or do they flash once in a while? Mine just stay on. Thanks
Looking for the original factory mounting brackets and hardware for the original WCS94 topper ( https://www.marcospecialties.com/pinball-parts/31-1925-18-SP ) Thanks for your time.pasted_image (resized).png
Quoted from Dr-pin:Does anybody make and sell new playfields for this beautiful game?
I wish! Lotta folks need them and want them.
Quoted from Wanimal:Where can I get those at?
I'm looking into changing the LM323K regulator due to heat on my WCS94 driver board. Has anyone installed the PSU5 replacement in a WPC-89 board? How did work?
https://www.ezsbc.com/index.php/featured-products-list-home-page/psu5.html#.XfLSrvyIZzm
Thank you
It has always bothered me that a WCS94 topper was produced, but not the hardware to properly install it. I have never seen factory hardware installed with the topper. I believe the hardware for the topper was never mass produced. I'm almost ready to install my topper with brackets I've made. The brackets are from solid 3\16" brass plate. Solid brass wood screws and brass plated rivets. I really wanted to stick with the original gold / brass theme. I haven't polished the brass yet, only sanded with 500 and 1000 grit - wet. I'm still trying to perfect the rolling of rivets.
IMG_20200212_122913826 (resized).jpgIMG_20200212_123150936 (resized).jpgIMG_20200212_182517610 (resized).jpgIMG_20200212_182528206 (resized).jpgDoes anyone have a link to where I can purchase the screw and washer assembly for holding down the soccer ball? Someone sell me one! I understand that this screw is not necessarily needed, but I still want the factory part.
Quoted from Its_me_aj:Joined the club with a pretty exceptional example of a game. A good cleaning and a few little things here and there and it will be solid. Put some LEDs in tonight and I’ll get the rest finished after I put a list together.
Hey Its_me_aj, Congrats on getting this awesome pin. Mine is never leaving - too unique. You need the metal stops that are at each ramp exit. It reduces the impact on the plastic. I'm not sure if anyone sells the metal stops. You may need to fabricate these.
Quoted from KSUWildcatFan:Fire up the hate mail, I finally pulled my rails off.
Now I need to find a set of brass hinges. I think that'll be sufficient for a bit.
[quoted image][quoted image][quoted image][quoted image]
This is exactly my plan. This game truly deserves the brass treatment. Need the details KSUWildcatFan!!
Quoted from nitrojcrawf:Has anyone used both the Mantis and Cliffs protectors together?
I have both. I do have clear silicone holding the Mantis scoops down. It's overkill for home use but I enjoy having that extra protection.
The new CPR playfields are available. Pricey but beautiful. Why does Vegas enter my mind when I say that
Quoted from fatality83:Just saying how much the boston tea party makes me smile each time I see striker chugging the tea
I don't believe he is drinking tea
Sold my WCS94. If your looking for a mini-playfield replacement or a spare. https://pinside.com/pinball/market/classifieds/ad/134364
You're currently viewing posts by Pinsider wombat.
Click here to go back to viewing the entire thread.
Wanna join the discussion? Please sign in to reply to this topic.
Great to see you're enjoying Pinside! Did you know Pinside is able to run without any 3rd-party banners or ads, thanks to the support from our visitors? Please consider a donation to Pinside and get anext to your username to show for it! Or better yet, subscribe to Pinside+!
This page was printed from https://pinside.com/pinball/forum/topic/world-cup-soccer-94-owners-everyone-welcome?tu=wombat and we tried optimising it for printing. Some page elements may have been deliberately hidden.
Scan the QR code on the left to jump to the URL this document was printed from.