I am new to this club. My game also has very bad ghosting issue. To solve this issue I just ordered a few non ghosting LEDs for all the inserts plus sunlight LEDs for all the G.I. I also using these types of LEDs in my CFTBL. Based on my previous experience these Comet LEDs will make my game look amazing. Now I am waiting patiently for my order to arrive.

Yes, my one ghosted badly. I need to use non-ghost LEDs from comet. However, if I could do it all over again. I will buy stern OCD LED board and just use 2SMD. On the other hand, it is worth it to install Cliffys protector on your machine. Enjoy it!

Hi there

Please help me! My current issue is, during the game and I am in my last ball, I locked one or two balls at the couch, if I drained. The one or two balls that I locked at the couch won’t release the balls during the game ending scene. In other words, if I stared a new game immediately, my new game already got one or two balls locked. It wasn’t like that before.

Anyway before this ball lock issue occurred, my mystery award was disappeared then I resetted the whole game to factory settings then my mystery award is back but follow with this ball lock issue.

In general, all the switches are fully functional during the test mode and if I closed the coin door during the test mode and put three ball into the ball trough, game will release three balls to the shooting lane but those three balls will just stay at the shooting lane.

My questions are
1. How can I make the game release all the ball from couch? Is it any setting I need to be aware of?

2. Is it normal my game release 3 balls to shooting land during switch testing mode (two other balls will remain in the ball trough)?

Game play normally apart from the couch ball lock when the game is finished.

Best regards
Paul.

Hi Maken and Ralpwiggum

Thank you for your help. My game is back to normal.

Hi there

Hope someone can help me. My TSPP still has a resetting issue. Based on Silverball website. I can replace the Bridge (BRDG21) to sort this issue

Link: http://www.silverballrestorations.com/category/pinball-repair-2/

Now based on the stern manual, the replacement for 5v DC logic should be 35a @ 100v (pic 1). However, I cannot find anything @ 100v. After more research at pinside. I found this link:

https://pinside.com/pinball/forum/topic/brdg21-on-whitestar-what-is-the-correct-one-to-order

It looks like 400v is workable in this situation. Sorry, I am not an electronic technician. I just try to fix this issue myself without creating more issue in the future.

My question is. Can this 35a @ 400v bridge does the same job as the other one listed by stern (35a @ 100v)? If yes, I would like to get one from this website

Link:
https://www.jaycar.co.nz/400v-35a-bridge-rectifier/p/ZR1324

Once again thank you for your help.

Best Regards
Paul

image (resized).jpeg

My one was caused by low voltage. Now it is fixed. I took the board out and clean all the connectors

Hi there

I just have an issue here. My TSPP is not giving any Mystery award at all. I checked the switch everything is working fine. I just wonder is it a software setting issue or rom corrupted issue?

I can fix this issue by re-setting the machine but is it normal? Does the machine stop giving mystery awards after how many games you have played?

Please help.

Hi GeekedOnPinball

I am using Sunlight in my TSPP. I really like it.

E0F25E86-73B7-4239-BFD3-66A6FF245D7E (resized).jpeg

Hi there

These are the pictures for J2 and J3.

Hope it helps
D76D5051-DC8A-4B37-9818-CB7BC828F516 (resized).jpegFCCA1A90-BC8D-44E1-919F-ADA8646DAF2C (resized).jpeg