Hello!
I just bought a ToM
When are the 2 drain save magnets supose to save the ball?
The magnets work fine in solenoid test and the switch test. And the Eddy sensors works fine.
You're currently viewing posts by Pinsider tjohejsan.
Click here to go back to viewing the entire thread.
Hello!
I just bought a ToM
When are the 2 drain save magnets supose to save the ball?
The magnets work fine in solenoid test and the switch test. And the Eddy sensors works fine.
Quoted from lyonsden:When you hit the hocus pocus targets on the left, the insert will light up and start to flash. When it is on/flashing, the magnet saves will work (assuming they are adjusted correctly and sensing the ball).
Thank you!
They work fine
Hmm puting my game together and there sometging wrong here i think!?
Should the long metal hex just hang there?
If i am not remebering wrong there should be 2 more short hex post that is just hanging in the air and suporting the ramps?
Maybe someone can take a picture?
I have a problem with my trunk
I have a new pindora box trunk board.
But sometimes the trunk stops working, and it shows " trunk error".
I start the trunk test, and it shows error.
Then i test the trunk pressing (+) (-) in test mode.
Then it works fine again.
But then stops working when playing again.
I bought a new pindorabox board. Thinking that was the problem?
And as seen in the pictures. This is how the optos are lining up when the two locks on the trunk is showing.
I think its wrong?
The spring/gap on the interuptor is facing left where the screw is.
I have problem with my trunk it sometimes stops working.
After trunk test mode it works again for a short while.
I bought this new trunk board, but still same problem:
Art.nr: FP-A-19749
Brand new design Theatre of Magic Trunk Opto Board. Based on Leon's Trunk Fix. Will automatically adjust! Direct replacement board for the original Theatre of Magic Trunk Opto Board.
Would the new board (look post before me) work?
Quoted from Tjohejsan:I have problem with my trunk it sometimes stops working.
After trunk test mode it works again for a short while.
I bought this new trunk board, still the same problem:
Art.nr: FP-A-19749
Brand new design Theatre of Magic Trunk Opto Board. Based on Leon's Trunk Fix. Will automatically adjust! Direct replacement board for the original Theatre of Magic Trunk Opto Board.
Quoted from pinballinreno:Gear box might have to be cleaned and re-lubed.
Also motor might have to be cleaned out. You can clean out the motor with circuit cleaner. The ends come off if you are careful.
Does wonders but it's a pain.
Fortunately you only have to do it once every 20 years.
After that maybe get the new board from german-pinball
Never thougt about cleaning the gears and motor, i'll start with that.
Thanks for your advice
Hello! Trunk issue here!
I guess this not the first post about trunk issue.
But i cannot find the problem i have.
My issue is that the motor dont stop in line with the optos on the optos board. Most times it stops just right after.
I have new :
Motor and gearbox
Tried:
2 different opto boards (original, pindora box)
Tried a working:
Motor controller board
2 different opto interrupter
: Rev 1.3x installed
16827768901955602397320423316771.jpg16827770198887675513131038305976.jpg
You're currently viewing posts by Pinsider tjohejsan.
Click here to go back to viewing the entire thread.
Wanna join the discussion? Please sign in to reply to this topic.
Great to see you're enjoying Pinside! Did you know Pinside is able to run without any 3rd-party banners or ads, thanks to the support from our visitors? Please consider a donation to Pinside and get anext to your username to show for it! Or better yet, subscribe to Pinside+!
This page was printed from https://pinside.com/pinball/forum/topic/theatre-of-magic-club?tu=tjohejsan and we tried optimising it for printing. Some page elements may have been deliberately hidden.
Scan the QR code on the left to jump to the URL this document was printed from.