You're currently viewing posts by Pinsider onemoresean.
Click here to go back to viewing the entire thread.
I picked up a Shadow a couple of months ago. Seller claimed that it was 80% shopped.
I added Titan rubber, Comet LEDs, and a new DMD.
I love this game!
Quoted from waldo34:That's the one. Interesting topper in that I can't find out any information about it.
https://pinside.com/pinball/forum/topic/pinball-toppers-in-the-works/page/2
Quoted from per3per3:Did you put Mylar on top of it? How about some details on how you applied the kwik wood?
Thanks!
Clean with Naptha, and tape off so that just the damaged area is exposed.
Apply the Kwikwood and smooth with a new razor blade leaving a hair more than needed.
Sand until smooth and level with the playfield. I used 320, 400, and 600.
Apply new decal.
I'm sure this isn't the proper way to do it, but it was the way I did it.
Quoted from ramegoom:I had repeated problems with the broken spot welds on the ramp and this seemed to fix it. The welds are broken, but the plastic with four screws holds it in place firmly, and the ramp works 100% even with the disconnected sides.
Nice!
How much for one?
Quoted from lpeters82:What's the deal with the green dot? I've seen them before but didn't know why people were adding it to their games.
The green dot protects the playfield from sanctum magnet wear and covers previous damage.
Quoted from BioBa:I just did a refurb on my Shadow. Have this post left over??
Any idea where it might go. Have taken off all ramps and plasticsduring the refurb.
[quoted image]
Do you have a post between the trough and shooter lane?
Quoted from RockBass14:Is there a fix for the start scene eject? Mine ejects the ball across to the wall and it bounces back in and repeats for a while. Sometimes it eats up to 10+ seconds into my scene!
My Shadow was doing the same thing.
I bent the solenoid bracket toward the backbox about 1/8" and it ejects fine now.
Quoted from RCA1:Not really what I think of as an airball protector, but not sure what else you would call it.
Shadow ramp switch extender
Quoted from okgrak:Here is a very minor “mod” that looks quite nice on this machine. These are the clear coin inserts sold by pinball life with some comet purple passion bulbs behind.
[quoted image]
Looks good.
I went with the clear inserts with green leds.
Quoted from misfitdart:Hello all, I just did a pf swap out and having a hell of a time remembering where this piece went....
[quoted image][quoted image]
Might be for your battlefield.
BEFFAC3F-51D0-4B22-B6C9-AC421D598687 (resized).jpegEE735CCC-3952-411E-BCF9-D25E27ED424E (resized).jpegQuoted from DropGems:What’s up guys… new shadow owner here and pretty much a total noob at pinball repairs. I’m having issues with the left diverter, diverters work but position is like almost in the middle on the one side. It’s super annoying as I get a lot of rejects. Is this easy to fix? Thx!
[quoted image]
Check for a broken or missing spring before adjusting diverter.
Quoted from acedanger:Got a few sets left over. FYI shipped all orders this morning.
[quoted image]
I received the phurba opto covers today. Here’s a couple of pics of them in the machine.
26A188DA-D405-4D2C-9763-4F539FBAD251.jpegB19FDF41-022C-4F25-9A9A-D1B68866646C.jpegQuoted from flashinstinct:Free shadow decal set if you post on this thread in less than 30 minutes
I could use a set!
Quoted from allsportdvd:Putting back together my wire forms has been a challenge on this game
Can anyone share what their setup looks like on the right hand side? Where zip ties go etc?
You're currently viewing posts by Pinsider onemoresean.
Click here to go back to viewing the entire thread.
Wanna join the discussion? Please sign in to reply to this topic.
Great to see you're enjoying Pinside! Did you know Pinside is able to run without any 3rd-party banners or ads, thanks to the support from our visitors? Please consider a donation to Pinside and get anext to your username to show for it! Or better yet, subscribe to Pinside+!
This page was printed from https://pinside.com/pinball/forum/topic/the-shadow-club?tu=onemoresean and we tried optimising it for printing. Some page elements may have been deliberately hidden.
Scan the QR code on the left to jump to the URL this document was printed from.