You're currently viewing posts by Pinsider Digduglus.
Click here to go back to viewing the entire thread.
A few more questions -
Are the pop bumpers supposed to be weirdly shaped? trying to figure out if they are like that naturally or if mine has chips out of it.
Any suggestions for a good topper?
Planning on Palantir mod, any other amazing mods I should seek out?
Thanks again
Thanks for the suggestions everyone!
Got the color dmd and palantir ordered!
is it worth it to upgrade speakers? Speaker recommendations? Loving this game
Just picked up a LOTR that had been routed a few years ago. Some good things, some not so good. Has color dmd, path of the dead mod, needs a shop job, some guy spray painted the wireforms gold. Any thoughts suggestions, recommendations before i get started?
20200516_104829 (resized).jpg20200516_152201 (resized).jpg20200516_152217 (resized).jpg20200516_152220 (resized).jpg20200516_152157 (resized).jpg20200516_152213 (resized).jpg20200516_152155 (resized).jpg
LOTR didnt come with all switches connected. Any help identifying where these go would be greatly appreciated
20200516_232732 (resized).jpg20200516_232738 (resized).jpg20200516_232745 (resized).jpg20200516_232813 (resized).jpg20200516_232817 (resized).jpg20200516_232824 (resized).jpg20200516_232832 (resized).jpg20200516_232852 (resized).jpgQuoted from Pin_Guy:All you have to do is look at the color of the 2 switch wires, then locate the switch that uses those colors on the switch matrix.
For example if your connector contains a White wire with an Orange stripe and a Green wire with a Blue stripe, it would go to switch 43 (Left Top Lane).
[quoted image]
If you are still unsure of the location, you can fine the switch number on the playfild switch locator shown below.
[quoted image]
One of the connectors you show has red and yellow wires, this is not a switch connector at all, its a lamp connector and you dont want to put this in the wrong spot. It should be fairly easy to find out which lamp isnt working, or you can look it up in the lamp matrix using the exact same process as the switch matrix.
Got it all back together! Thanks chief. Still needs a lot, especially a flipper rebuild, but everythings connected. Thank you again!
Anyone have or know where to find an extra #07 plastic? The one that holds the Uruk holding the head? (Back right corner of the machine by the tilting tower) My machine didn't come with either of them. I found an Uruk online but can't find anything but complete plastic sets.
15897541880708478668418032859913 (resized).jpg
Quoted from yyyyyikes:Reckon I have a spare...you need just the plastic?
I think.... probably the figure holder that goes on top as well, although I think I saw that Pinbits sells replacement figure holders. I'll send you a DM.
Quoted from yyyyyikes:Reckon I have a spare...you need just the plastic?
BIIIIIIG shoutout to Yyyyikes for helping me out with the 2 plastics I'm missing. Didn't want to have to purchase a new full set. Thanks again!
In the middle of restoring my LOTR. (Ramps and wireforms are off to Pinball plating for brass) and I noticed my #6 plastic (far back left corner) is broken and missing. (This machine was heavily routed before I got it) Anyone know where I can pick up a spare #6 and maybe an Arwen (even a repro is fine) plastic? I'd like to exhaust other options without dropping crazy prices for a full set. If anyone has spares I could probably use the extra thick plastics and a backboard decal, but now I'm just being picky about mine. More than happy to pay if anyone has spares!
Quoted from DeathHimself:They are overseas I have dealt with them in the past without any issues.
https://www.pinball.center/en/shop/pinball-parts/playfield-parts/plastics/7205/arwen-plastic-for-the-lord-of-the-rings
I thought pinball center stopped delivering to the USA
And on that note, if there IS anyone able to get a pinball center shipment delivered to me in the US, I'd be happy to pay for the hassle.
Hey folks, i picked up a heavily routed LOTR a while ago and have finally started going through it.
Both playfield wood rails need replaced due to damage. Does anyone have decent photos of the posts and holes on the left rail? Trying to figure where these spiky posts go on the new left rail im building.
Quoted from LOTR_breath:I hope this helps.[quoted image][quoted image]
Exactly what I needed, thank you!
Quoted from drummermike:It goes on the end of the left ramp. It replaces the ugly piece of plastic hanging over the ramp.
This one? Sorry im not fully reassembled. Lots of parts in the tumbler at the moment. Thank you in advance
20210117_192112 (resized).jpgQuoted from Morgoth00:Here is a pic I had on hand
[quoted image]
Perfect! Thank you! Just needed to see the order they went in
Quoted from Chalkey:I think the middle one is a clear protector for the gimli saucer or the shire area and the one on the right is a key fob. Is the one on the left also clear / no print? Is it a figure mount?
Middle was shire protector, right is key chain. No clue on left
You're currently viewing posts by Pinsider Digduglus.
Click here to go back to viewing the entire thread.
Wanna join the discussion? Please sign in to reply to this topic.
Great to see you're enjoying Pinside! Did you know Pinside is able to run without any 3rd-party banners or ads, thanks to the support from our visitors? Please consider a donation to Pinside and get anext to your username to show for it! Or better yet, subscribe to Pinside+!
This page was printed from https://pinside.com/pinball/forum/topic/the-lord-of-the-rings-journey-begins-members-club?tu=Digduglus and we tried optimising it for printing. Some page elements may have been deliberately hidden.
Scan the QR code on the left to jump to the URL this document was printed from.