Hey guys looking for some help , need photos of the drop target installed from factory sample or proto games .
I’m having an issue with my drop target coil and believe it’s wired incorrectly .
All help is greatly appreciated,
Thank you
You're currently viewing posts by Pinsider Localspeedshop.
Click here to go back to viewing the entire thread.
Hey guys looking for some help , need photos of the drop target installed from factory sample or proto games .
I’m having an issue with my drop target coil and believe it’s wired incorrectly .
All help is greatly appreciated,
Thank you
Quoted from Sciddleybop1980:I think of you click image gallery in this thread there’s a few pics on here from memory
Going to dig through now . was even looking at AFM wiring but no luck .
THX Sciddleybop
Quoted from Localspeedshop:Hey guys looking for some help , need photos of the drop target installed from factory sample or proto games .
I’m having an issue with my drop target coil and believe it’s wired incorrectly .
All help is greatly appreciated,
Thank you
NO LUCK
Quoted from bssbllr:I can look at my drop target assembly but I added it on so it is not a prototype so might not help.
yes nothing in schematics or solenoid charts either as its not there .
Quoted from bssbllr:Here is the direction I followed and mine works great. I will take pics if needed but my wiring color scheme may make it a little difficult. Lmk. On the pics.
https://pinside.com/pinball/forum/topic/i-just-added-a-drop-target-to-our-dirty-harry
Sadly I tried to read it a few times , doesn’t make any sense to me .
I pulled my driver board from theatre of magic to isolate any transistor issues ... acts the same. Leads me to only think it’s wiring .
8E0B8349-0533-4EF2-A1FA-6FB9B67ED790 (resized).jpeg902C6D91-2B1F-4E79-8D1B-84D1D64B8DA8 (resized).jpegC4108ED2-2257-40EE-A25B-529E6B054F8B (resized).jpegQuoted from bssbllr:I had to read several times as well. Re read these a couple times this is for just the coils. One side borrows from coils on the playfield and the other side goes to back box. It is explained pretty good and works but might be different then factory wiring.
My colors are different then the explanation but you could always look back at the posts pics for color guide to match explanation.
[quoted image][quoted image][quoted image][quoted image][quoted image][quoted image][quoted image][quoted image]
I appreciate all the pics , but yes totally different looking in the factory wiring ... I have the coil not locking on now but its going to ground somehow as coil gets hot quick and have to shut it down , collapsed a coil last night already .. will continue searching .
Quoted from Cash_Riprock:Do you still need pics?
Yes for sure I think I may have it figured out now .
But still want to verify what the factory did as not any manuals on the right wires since this was the 7th proto and not everything matches up .
My last issue is :
Righ ramp gate is firing under test mode but somehow makes the 25 drop target test solenoid fire as well ..
Same with left top popper under test makes the left ramp diverter fire as well .
I’m not reading in manual that the tie back at 122 6-7-8-9 is specifically for the three switches mentioned .
Note under solenoid test drop target 25 fires properly .
Quoted from Cash_Riprock:Sure thing. I’ll be able to take them tomorrow.was suggested
Howdy Ryan
Here ya’ go. If something else needed lmk.
I have a Color Display in my game, (which I don’t think affects what you are looking at in your pm pics) otherwise factory sample w/Drop Target.
[quoted image][quoted image]
I have no connectors at J123 & J124.
Wiring at J122 is different from yours.
122 is same so is 107 .. see if you can find these connectors
538BA617-406E-4789-832A-E12526134B6B (resized).jpegYou're currently viewing posts by Pinsider Localspeedshop.
Click here to go back to viewing the entire thread.
Wanna join the discussion? Please sign in to reply to this topic.
Great to see you're enjoying Pinside! Did you know Pinside is able to run without any 3rd-party banners or ads, thanks to the support from our visitors? Please consider a donation to Pinside and get anext to your username to show for it! Or better yet, subscribe to Pinside+!
This page was printed from https://pinside.com/pinball/forum/topic/the-dirty-harry-club?tu=Localspeedshop and we tried optimising it for printing. Some page elements may have been deliberately hidden.
Scan the QR code on the left to jump to the URL this document was printed from.