Quoted from cpr9999:Approximately $685 US dollar (apron plus shipping).
Where can one purchase the apron? Thanks
You're currently viewing posts by Pinsider Dexter.
Click here to go back to viewing the entire thread.
Quoted from cpr9999:Approximately $685 US dollar (apron plus shipping).
Where can one purchase the apron? Thanks
Quoted from Rensh:Just sent an email to [email protected] mentioning full name, adress en TBL serialno.
Than you will get an invoice for exact amount incl shipping. Next step is paying it and than shipment will be done .
Thanks - so I need to wait until my game is delivered and I have a serial number before ordering the apron? On order with CoinTaker.
Ryan
Quoted from Rensh:For those who have not yet registered
https://forms.dutchpinball.com/register
If you have ever had contact with me for service purposes, those are already entered in the system to.
Date is stated as optional but is needed for the moment. Is gonna change to be optional.
If you wanna know if you are already in the system sent me a PM with name and serialnumber. I can check and let you know.
Done. Thanks Rensh. Loving the game! Top 10 for sure in my book!
cpr9999 - Sent you a few PMs. Looking to purchase your mods. Please reach out to me. Thanks - Ryan
Quoted from tk375:Clear vinyl tubing to be correct. 1/2 thick. You can buy a foot for under a dollar.
Can you send a pick of what you mean and an install?
I am having the hardest time adding art blades to my TBL. No issue with the right one with the upper playfield. But the left one keeps getting ripped while adding. I have gone through two sets already. I use the wet method with Rapid Tac and have had no issues on any other games until now. Is taking the playfield out hard? Any advice?
Thanks
Ryan
Quoted from mac2444:I put mine in dry, pushed the playfield to one side for the install and used a pinblade protector as soon as it was in. then slid the playfield to the other side for the second one. It's tight but they went in ok.
Used these protectors: https://www.pinballlife.com/interior-cabinet-protector-blade-set.html
Good luck with round two!
Thanks - I have those protectors and use them on all my machines. I am building up the courage for a third try. This is costly
Quoted from ThePlumber:I'm part of the club now! SO Excited! S/N DP-01-00688. Very happy to have played a few games. Two complaints, 1) side rails damaged by head pressure, corner guards would've taken that possibility out (hoping distributor will take of me) and 2) my left loop goes SDTM almost every single time. How about you guys? does yours do the same thing when you hit a nice crisp left loop shot? THANKS AGAIN FOR YOUR TIME AND INPUT.
My side rails came the same way. Cointaker sent me a replacement - but not an easy task removing!
Quoted from ThePlumber:Appreciate the heads up. She has indicated she is sending me another set. I guess I'll mentally prepare myself for the patient removal process. Any tips?
Get a sharp putty knife and slowly start to pry it up. Don't try a hairdryer and heat - it did nothing.
Quoted from Rensh:The switch is in the scoop has been the one needing the most adjustment-attention-complaints of all switches in TBL m. This solution will end that.
If you are not having any issues, like most users, no reason to upgrade. Don’t fix which ain’t broken is what I say.
Rensh - I am having this issue sometimes - how do I go about getting the fix/upgrade? Thanks
Ryan
Quoted from Dav_59_fr:Plexi blades from Custom Pinball (France)
https://www.facebook.com/custompinball
And few mods from cpr9999
And the playlist from JYEAKLEY
[quoted image][quoted image][quoted image]
I just received mine - did you drill/cut a hole for the hinge bolts or did you just put this right over?
Quoted from marksf123:I got mine too and have the same question?
He just responded to a post I had on Facebook and said put it on with Bolt removed and then drill 11mm hole and reattach bolt.
Quoted from 1956PINHEAD:For those who are inquiring about which flipper kits and parts to order for your machines feel free to send me a message, I'll be happy to answer any questions you may have.
John
Precision Pinball Products
John was very helpful in helping me determine which set to purchase. Thanks - Ryan
Quoted from ezatnova:Just came to post and ask about that topper.
To clarify, Lior / little shop of games is also coming out with one too, correct? Curious how they will compare and differ.
@Lior - You need to show yours ASAP!
Quoted from wcbrandes:there are only 100 of these, i'm sure Lior will be fine.
I'm not going to buy two toppers - so want to see what liorillusion is offering. Will be hard to beat this one.
Quoted from Rensh:Interesting to see how a magnetic decal will attach itself to a wooden panel
These appear to be peel and stick for this title because of the wood.
You're currently viewing posts by Pinsider Dexter.
Click here to go back to viewing the entire thread.
Wanna join the discussion? Please sign in to reply to this topic.
Great to see you're enjoying Pinside! Did you know Pinside is able to run without any 3rd-party banners or ads, thanks to the support from our visitors? Please consider a donation to Pinside and get anext to your username to show for it! Or better yet, subscribe to Pinside+!
This page was printed from https://pinside.com/pinball/forum/topic/the-big-lebowski-official-club-thread?tu=Dexter and we tried optimising it for printing. Some page elements may have been deliberately hidden.
Scan the QR code on the left to jump to the URL this document was printed from.