Here’s some T2 under glass instructions and retro fuse labels I made for the back board.
Download it from my post here if you want a High Res printable version...
https://pinside.com/pinball/forum/topic/t2-cards-fuse-labels#post-4244212
You're currently viewing posts by Pinsider zimbakin.
Click here to go back to viewing the entire thread.
Here’s some T2 under glass instructions and retro fuse labels I made for the back board.
Download it from my post here if you want a High Res printable version...
https://pinside.com/pinball/forum/topic/t2-cards-fuse-labels#post-4244212
Quoted from kaz1961:Its official, I am a T2 owner again. Gotta remember to keep this one!
Awesome, as my old man once said... she's a keeper.
Quoted from Averell:...This bad guy will replace the plastic skull on the playfield later.
Some work to do but at the end it will look much more better as the plastic crap.
Is that the original T2 Skull? If not, can someone post a pic of the original skull.
Interesting. If the ball shatters the skull... bonus points!!! Careful it doesn’t damage the playfield
Quoted from terryb:The right/left eos switches are in the same column as the launch button so it could be a switch matrix problem. Go into switch test and see if more than one switch indicates closed when either eos switch is closed.
Any work done on the game prior to the problem arising?
Run a switch test to see if one is bad. Could be a bad switch, diode or short issue.
Can anyone help me get an electronic coin mech working with my T2?
Original post here... https://pinside.com/pinball/forum/topic/c220-coin-controls-wpc-a-14689-1-interface-help
Anyone know how to fix the "cannon can't hit lowest target" issue?
I posted the problem in detail over here..
https://pinside.com/pinball/forum/topic/t2-cannon-alignment-short-of-lowest-target
Quoted from tezting:Can someone with the original backbox give me measurements for the three yellow "lines" on this image? I forgot to measure and have to install new decals. Would be great help so I can align perfectly.[quoted image]
What are the 3 yellow lines? I don't have those on my back box, so not exactly sure what you want measured?
Quoted from tezting:Can someone with the original backbox give me measurements for the three yellow "lines" on this image? I forgot to measure and have to install new decals. Would be great help so I can align perfectly.[quoted image]
On my backbox:
- blue starts 53mm from base
- top (right edge) is flush (aligned) with edge
- bottom (left edge) graphic starts 13mm in from edge
I think you could centre the left and right edges and it would look fine
Quoted from Blitzburgh99:Need help with problem:
Gun not firing when trigger pulled
All switches work in test mode. Solenoid fires in test mode. Gun calibrates. Trigger launches ball into playfield. But when Ball goes into gun fir jackpot shot, the trigger doesn’t fire the ball out. Gun rotated but trigger doesn’t shoot it.
What next?
Did you check the ball load micro switch in the canon in test mode... ie. does it register?
Also, when the ball is in the canon, is it fully depressing the switch. I replaced mine a while back and had to adjust the position so that the ball keeps the switch depressed when loaded.
Quoted from tezting:Sorry if they where not so visible
[quoted image]
Hehe, no dramas. I worked it out just after posting.
On my backbox:
- blue starts 53mm from base (right line in photo)
- top in photo (right edge) is flush (aligned) with edge
- bottom in photo (left edge) graphic starts 13mm in from edge
I think you could centre the left and right edges and it would look fine
Quoted from DropTarget:soooo,
I'm putting on new rubber, what's the consensus, Black or white?
Prefer the white, only because that’s what I remember on the original that I played. Williams sometimes changed rubber and flipper colours depending on what they had in stock at the time. So some people will recall slightly different colour combos. Call me nostalgic, I will always pay more for a machine that is original. It’s purely subjective and personal preference.
Quoted from grimholtz:Hey guys,
My shooter gun only operates to launch the ball. It doesn't work when the ball is in the canon. What should I look for?
Thanks for any advice.
1. Check the microswitch in the canon. It tells the machine that a ball is present.
2. Under the playfield, check the black wheel with notch under the canon. Make sure the micro switch is adjusted correctly to allow the ball to fire when the canon has passed the ramp. Also check that micro switch.
Doesn’t seem like a fuse if it’s firiing, more likely one of the micro switches or even possibly the gun trigger switch
You're currently viewing posts by Pinsider zimbakin.
Click here to go back to viewing the entire thread.
Wanna join the discussion? Please sign in to reply to this topic.
Great to see you're enjoying Pinside! Did you know Pinside is able to run without any 3rd-party banners or ads, thanks to the support from our visitors? Please consider a donation to Pinside and get anext to your username to show for it! Or better yet, subscribe to Pinside+!
This page was printed from https://pinside.com/pinball/forum/topic/terminator-2-clubmembers-only?tu=zimbakin and we tried optimising it for printing. Some page elements may have been deliberately hidden.
Scan the QR code on the left to jump to the URL this document was printed from.