You're currently viewing posts by Pinsider luckycreature.
Click here to go back to viewing the entire thread.
Quoted from Manny65:Welcome to the club!!
To be honest if you have no errors, just focus on playing the crap out of your machine
The only preventative maintenance would be the tieback - there are plenty of sites showing details (Google "STTNG tieback") here are a few:
https://pinwiki.com/wiki/index.php?title=Star_Trek:_The_Next_Generation#Diode_.22Tie_Back.22_missing_causes_8-Driver_Board_transistor_to_fail
https://pinside.com/pinball/forum/topic/sttng-tieback
There are various things that can fail on STTNG but I wouldn't worry about them until they do fail
- cannon wire looms are known to fail from the constant twisting
- there are a lot of optos used, especially in the VUKs for the cannons as well as the trough. These are prone to colder solder joints.
- the single drop target, on the right orbit above the pops, can sometimes need a bit of attention
Have fun!!
Can you tell if mine is done already from these pictures or if I still need to do it?
IMG_20200810_204639 (resized).jpgIMG_20200810_204649 (resized).jpgQuoted from Pin_Guy:They SHOULD be connected to J120; that being said, J120 and J121 connectors are electrically identical and keyed the same, so it could be on either one, you will know by the wire colors.
[quoted image][quoted image]
Thanks. Ill look tonight. I used the manual for the fuses, but couldn't find this page...
Quoted from Pin_Guy:When a connector burns like that you really should replace both the connector and the header. That being said, I've seen boards that were severely damaged by folks that was "fairly certain" or "pretty sure" they could replace the header. Unless you know for a fact you can do it because you've replaced dozens or hundreds of headers just like it ... you may not want to try it.
While it will work if you just move the wires to J121 it's less than ideal; but is still better than damaging the board.
Thanks for all your help.
Quoted from Zitt:It this even a picture of a stng machine? Not sure what I'm even looking at
Sorry. It's the white plastic bar under the guns . It's broken at the bottom.
Quoted from Mathazar:You need a roll pin punch set and a lot of patience. I had to take the whole cannon assembly out, put it on my bench, and hammer away. Broke one of my roll pin punches in the process, but I got the pin out.
amazon.com link »
Thank you. What a pita
Can someone take a picture of the correct assembly of the under Borg start mission shot. It stopped working and it looks like something is missing from my assembly. Thanks
PXL_20201024_135240820 (resized).jpgPXL_20201024_135244152 (resized).jpgPXL_20201024_135244152 (resized).jpgPXL_20201024_135258515 (resized).jpgQuoted from monkfe:Your white/purple wire is broken off....look closely in the pic you posted
Aha. So it is. I'll get that fixed tonight . Does everything else look right?
Quoted from Pin_Guy:You have a small hack that was done, probably to replace a broken target reset plate.
[quoted image][quoted image]
[quoted image][quoted image][quoted image]
Thank you. These pictures help alot.
You're currently viewing posts by Pinsider luckycreature.
Click here to go back to viewing the entire thread.
Wanna join the discussion? Please sign in to reply to this topic.
Great to see you're enjoying Pinside! Did you know Pinside is able to run without any 3rd-party banners or ads, thanks to the support from our visitors? Please consider a donation to Pinside and get anext to your username to show for it! Or better yet, subscribe to Pinside+!
This page was printed from https://pinside.com/pinball/forum/topic/sttng-owners-club?tu=luckycreature and we tried optimising it for printing. Some page elements may have been deliberately hidden.
Scan the QR code on the left to jump to the URL this document was printed from.