Has anyone with a topper tried to install Insider Connected yet? I went to do it today and there are no open Ethernet jacks on the node boards.
You're currently viewing posts by Pinsider selig.
Click here to go back to viewing the entire thread.
Has anyone with a topper tried to install Insider Connected yet? I went to do it today and there are no open Ethernet jacks on the node boards.
Quoted from Selig:Has anyone with a topper tried to install Insider Connected yet? I went to do it today and there are no open Ethernet jacks on the node boards.
I heard back from Stern and wanted to post here in case anyone else runs into this. They are working on official instructions, but there is an open Ethernet port behind the mini lcd. I just plugged my insider connected there and it works great. I think officially they are going to show how to move a cable from node board 8 so you can plug in closer to the reader.
Quoted from mbrave77:Regarding IC and topper. I finally have a topper coming(yea i paid a lot for it). I have IC setup already as I ran the cable to the open slot behind the backglass.
So if I get an ethrenet cable splitter and just have IC and topper plugged into that single backbox plug itll work?
I have the topper as well. The official instructions from Stern support are to plug into the extra port at the back of the mini display, but it sounds like the splitter is working for people as well.
Quoted from Schaitas:Thank you. But what if I have the external volume control /headphones in the coin door?
I never used the headphone jack so I switched to this: https://www.pinballlife.com/mm5/merchant.mvc?Screen=PROD&Product_Code=PBL-100-0062-00
Another bonus is that it is not an obvious knob for kids to mess with.
Quoted from TheClownpuncher:Where did you get the speaker logos? I've looked all over for them and can't seem to find any.
I think Doug at speakerlightkits.com has them
Quoted from GCS2000:Thanks for this info. This might turn the wife off on it unfortunately. She doesn't mind fast games but regular SDTM and brutal outlanes are not her thing.
Need to watch some more video to refresh things further.
I got the extended outlane post for the left outlane to make it easier "for my kids" lol. The right outlane is not as brutal if you close it up with the standard post. I do get sdtm from the horseshoe if the ball is ripping around it but for the most part it is pretty good. My kids and their friends always gravitate to SW even over Wonka. My son finally hit the hyperloop shot and went nuts when the ball started zipping around the loop. I am not a great player by any means but always have fun on this one. I will say it was super frustrating before getting the large left outlane post though. I am only okay at nudging and could never seem to save the ball from that monster.
Quoted from JakeFAttie:do you have a picture of this post in your left outlane? sorry I'm just not familiar with an "extended" outlane post but it sounds very nice!
Here’s a pic, but I love the R2 one posted here. May have to print one of those!
6CC1937B-21AE-47B5-8F88-C5372FBE42A2 (resized).jpegAnyone had issues with the mini lcd on the playfield? Mine went out. I checked and re-seated all of the hdmi connectors from backbox to middle to lcd and checked the cat cable from the node board. I have my IC connected to the open port on the back and that still lights up and works. Swapped the cat cables to verify it was not the one port, the IC works regardless of the port it is on. I am thinking my lcd died. I have a ticket in with Stern but after sending me the basic troubleshooting steps I haven't heard back. Going to reach out to my distributor as well. I haven't seen any posts about this here but figured I would ask.
Quoted from hiker2099:Just guessing but, break in the wire? or bad pin in the wire harness?
Yeah, I was thinking that but the IC still works which is getting power/data from the LCD cat cable that runs to the node board. I will try swapping out the HDMI cable and see if that is it.
You're currently viewing posts by Pinsider selig.
Click here to go back to viewing the entire thread.
Wanna join the discussion? Please sign in to reply to this topic.
Great to see you're enjoying Pinside! Did you know Pinside is able to run without any 3rd-party banners or ads, thanks to the support from our visitors? Please consider a donation to Pinside and get anext to your username to show for it! Or better yet, subscribe to Pinside+!
This page was printed from https://pinside.com/pinball/forum/topic/stern-star-wars-clubmay-the-force-be-with-you?tu=selig and we tried optimising it for printing. Some page elements may have been deliberately hidden.
Scan the QR code on the left to jump to the URL this document was printed from.