I am missing the cable to hook up the shooter rod can someone post pics of the actual cable to hook it up! I will have to email stern or see if someone can make me one
You're currently viewing posts by Pinsider TonyScoots.
Click here to go back to viewing the entire thread.
I am missing the cable to hook up the shooter rod can someone post pics of the actual cable to hook it up! I will have to email stern or see if someone can make me one
Quoted from Markharris2000:The shooter rod plate for a lighted amber rod has two LEDs cut into the surface. Those LEDs are wired to a couple of feet of cable with a .100" nylon connector on the end that plugs into CN15. Are you saying you got the amber rod and the shooter rod plate with the two LEDs installed, but the LEDs weren't connected to anything on the back?
I only have the Rod, no plate and no wires to hook it up unfortunately. I can modify the plate but would need to see if someone can make the wires for me. I have sent a few emails to stern but no response yet
Quoted from Markharris2000:Where did you get the Amber ROD? Is it the official Stern version? I thought that Stern ONLY supplied the shooter rod and mounting plate as a full kit. I am a bit confused what you have in hand right now. There are other non-Stern suppliers that have also supplied JUST THE ROD, but I am not sure Stern will sell you the lighted mounting shooter plate separately.
That said, I think it would be straight forward if you had some tech savvy person help you drill two LED's into the shooter plate and add the two 150-220 ohm resistors and a couple feet of stranded wiring and a nylon CN15 connector.
It’s an official Stern Rod, I bought it off OfferUp from a collector who sold his JP, unfortunately it’s my fault because when I bought it and then installed it a month and a half went by. I went to install and open the box only to see the shooter rod, for some reason I didn’t know at the time it came with a bracket & hookup wires. I have messaged the seller who says he doesn’t know where it is.
B6098EB0-4251-48C6-A8D9-00EF7D285B3C (resized).jpegQuoted from Markharris2000:Got it. There is a second cable missing. It has the CN15 keyed 6-position female connector at one end and the 4-pin MOLEX connector on the other. These are connected with about 2 feet of wire. You could make it if you got the connectors from Marco or similar and some hookup wire from home depot. Did you try to BUY it from Stern? It should have a part number. I think the parts guys can be reached at "[email protected]" and they can tell you what it would cost.
While I don't have one of these, here is what I think you are trying to build/buy (Note: pin numbers may be wrong as I am trying to do this visually from posted pictures):
[quoted image]
Mark,
Thank you so much! I am going to build it, I have also emailed stern to see what happens but thank you for so much help and info
Tony
Quoted from Markharris2000:Updated pinouts to reflect the JP1.0x software driving pin 3&4 on the CN15 connector.
[quoted image]
Thank you Mark, looking forward to making this
You're currently viewing posts by Pinsider TonyScoots.
Click here to go back to viewing the entire thread.
Wanna join the discussion? Please sign in to reply to this topic.
Great to see you're enjoying Pinside! Did you know Pinside is able to run without any 3rd-party banners or ads, thanks to the support from our visitors? Please consider a donation to Pinside and get anext to your username to show for it! Or better yet, subscribe to Pinside+!
This page was printed from https://pinside.com/pinball/forum/topic/stern-jurassic-park-pro-shooter-rod-installation-instructions?tu=TonyScoots and we tried optimising it for printing. Some page elements may have been deliberately hidden.
Scan the QR code on the left to jump to the URL this document was printed from.