You're currently viewing posts by Pinsider charger68.
Click here to go back to viewing the entire thread.
Quoted from Gritty:Is $12,500 from a distro now a reasonable price for an LE? I missed the boat on this one.
Plus shipping
Quoted from AmericanZen:I’m so excited, I got my new Godzilla LE today,but when I power it on it says “nodes 1,8,9, 10 not found.”
I checked all my connections, nothing seems loose, any suggestions?
Coin door closed?
Quoted from AmericanZen:Yes. I closed it and turned the power off and back on. Credit on free play but start button doesn’t light up and won’t start a game
Does it get to the start screen
Quoted from AmericanZen:Yep. Goes to start screen and says free play
Is the action button on the lock down bar flashing. If it is try starting a game with that then check your start button wiring
Quoted from AmericanZen:Action button and start button are not lit[quoted image]
Open coin door, on the left you will see a blue node board( node board 1). You will also see the start button and coin door wiring routed over to the board. Check the connections there. I have had bent pins from sloppy assembly. Also check all connections on that board. You may have to raise playfield
Quoted from AmericanZen:I pull the interlock button out and everything plays fine, when I close the coin door that hinge hits the white interlock?? button and pushes it back in and it won’t play
[quoted image]
Post pic of switch wiring, could be backwards
Quoted from AmericanZen:[quoted image]
Grey on top , Grey red down one no pin in middle
Quoted from PinMonk:I'm out of ideas as to the cause now.
I say just unhook the two connectors at the door, pop the switch out and reconnect the connectors so the switch is just inside the cab, unaffected by the door and will play normally with the door closed until you can troubleshoot with Stern.
You can troubleshoot switch with a meter if you have it out of cab
Quoted from marksf123:I am having an issue with the center spinner registering hits. I noticed that I never got the heat ray and Ebriah battle couldn't get completed on the center spinner even though I hit it a lot. When I spin the other two spinners I see it racking up points on the screen but when I spin the center it doesn't change the score and it is harder to spin. How do I adjust the spinner?
Thanks
Try loosening the hold down bolts on the switch
Quoted from teddyb73:Got some bad news. Looks like most of the distributors will only be getting 9 to 10 premiums in each due to the supply chain shortages for the first run
//<![CDATA[
window.__mirage2 = {petok:"0486f7cd3bafdc32be32feac1facf8b2fcaf6722-1636725692-1800"};
//]]>
Where'd you hear that
Quoted from radfordian3505:Don't tell me that as I have already paid for my premium early this week. My distributor has went radio silent on me since payment received. Got me all nervous on if I will get my game next week.
ditto
Quoted from radfordian3505:My distributor just confirm that the delay is a lie and my premium will be delivered Monday or Tuesday.
nice
Big ups to Rob at madpinball, Just got my shipping paperwork, Zilla premium inbound. Thanks again Rob
Just set up premium, everything checks out except right flipper. Coil doesn't fire from the test menu or from flipper button. Flipper button works for other functions. Swapped out node 8 with functioning one from elvira, same issue. No power to coil when attempting to test. Left shows pulse on meter. Any ideas where to start
Thanks in advance
Quoted from PinMonk:At the coil are the wires connected?
Yes they appear to be wired correctly
Quoted from PinMonk:You have the white post pulled out in the coin door frame when testing the coil from the system menu, right?
If so, at the coil are the wires connected? Give them a little tug even if they look connected, one may may not be.
Fiddled with wires while trying to fire the coul from test menu, no luck
Quoted from PinMonk:And you have the white post on the inside left of the coin door pulled out when trying to test the coil from the menu?
Yep
Quoted from PinMonk:Broken where? At the coil? At the connector, or inside the insulation along the way...
At the connector where the bare copper goes through the hole in plastic enroute to terminal
Quoted from nicoy3k:Hmmm when I go to update is says it’s up to date even tho I’m at .80
Same here, insider says I have no machines registered
Quoted from Nikko:Did the update this afternoon and everything worked fine. Played about 15 games, no problem. Then in the middle of a game the lower portion of the playfield went out - flippers and all the lights from the middle down. Is this a software update issue?
Sounds like a node board issue
You're currently viewing posts by Pinsider charger68.
Click here to go back to viewing the entire thread.
Wanna join the discussion? Please sign in to reply to this topic.
Great to see you're enjoying Pinside! Did you know Pinside is able to run without any 3rd-party banners or ads, thanks to the support from our visitors? Please consider a donation to Pinside and get anext to your username to show for it! Or better yet, subscribe to Pinside+!
This page was printed from https://pinside.com/pinball/forum/topic/stern-godzilla-official-owners-club?tu=charger68 and we tried optimising it for printing. Some page elements may have been deliberately hidden.
Scan the QR code on the left to jump to the URL this document was printed from.