Quoted from Kkoss24:Does anyone know the second run of premiums time frame ?Thanks in advance .
Sounds like Q1 2022. Maybe as early as Jan.
You're currently viewing posts by Pinsider Selig.
Click here to go back to viewing the entire thread.
Quoted from Kkoss24:Does anyone know the second run of premiums time frame ?Thanks in advance .
Sounds like Q1 2022. Maybe as early as Jan.
Quoted from tonyf1965:Thanks for closest thing we have for an update on the current number. Maybe 800 tomorrow-ish.
In the Stern virtual tour today, they showed #908 in final QA testing before boxing.
Quoted from rockrand:Both are fantastic!
Agree! I was surprised how much I liked the pro. It is just as fun. I still ordered the premium because the building mech is amazing, but the pro is still sweet.
Quoted from frankmac:Never owned a set of pin stadiums before but done properly it is amazing on this pin..
[quoted image][quoted image]
What shooter rod is that? Looks awesome!
Quoted from Waxx:How's Glenn's dolly?
Amazing. So easy going up and down stairs. Only thing to get used to is that it is pallet height. Great when moving the box off the pallet but a little tougher tilting the machine to get on it. All in all great buy though.
Quoted from Blakester:Has anyone used the Avengers Infinity Quest shooter rod on their GZ? Apparently it needs to be re-wired to work, it won't 'plug and play" unless mine is defective. I remember seeing that someone had but was unable to locate on this (long) thread. Thanks!
I put one on mine and thought I got a defective light. After researching, it sounds like the lights are software dependent. Haven’t been able to figure out how to get mine lit yet.
Quoted from BallyKISS1978:Anyone else receive their flame effect lights from speakerlights.com?
I ordered the second I got the email. Have had mine installed for a month and absolutely love them every time I turn on the machine. They are well worth the wait but be patient. Pretty sure Doug got swamped with orders and is building as many as he can.
I don’t think I have seen many pictures of the AIQ rod lit up on Godzilla so thought I would share. Thanks to Blakester for the instructions to wire it in. It ends up soldered to the rgb block that runs the UFO flasher, so it is semi permanent I guess but I think it ends up looking awesome.
2934DEAF-D7A3-45F2-99CA-2074CE203F78 (resized).jpeg5EA4BF29-B31B-4DB9-8104-1AD9D6DC157A (resized).jpegQuoted from Apollo18:Could you please post a picture of where you soldered the connection & install ?
Thanks.
Looks great.
The AIQ plugs are already separated to black for ground plug and 5v, R, G, B on another plug. Normally you would plug the powerRGB into CN15 but that requires software to drive the lights. I ran the 5v (yellow in my soldering) and RGB up to the block that has wires for the UFO RGB light. I just cut the moles from my AIQ and soldered/heat shrank a 5’ extension to the wires but if you have the parts you can just make a harness. My wires went:
AIQ Solid Red > Yellow
AIQ Red/Green > Red
AIQ Green > Green
AIQ Blue > Blue
Quoted from Chisox:Yes, this has been a common problem. Stern is working on a solution/replacement. In the meantime you can A.)Tell your distributor and ask for a new plastic B.)Buy one from Pinball life for $5 with your next order C.) Order the steel mod that someone on Pinside was making. If you replace it there have been posts suggesting everything from rubber pads on top of the plastic to shortening the travel of the plunger in the bridge coil to prevent further damage. I haven’t tried any of them yet so I have no opinion on what works best.
Mine has a hairline crack but no break. I put a small washer at the coil stop and that has restricted the motion just enough to not pound on the plastic but still plenty of room for the ball to exit at the start of bridge multiball.
Quoted from Pugster:Think I read it plugs in somewhere “factory” (same plug that AIQ uses?) and is interactive as is?
It does not work at the factory plug location, that requires the code to have it in there. A few of us have it working by soldering onto the RGB control for the UFO. This syncs the color and lights to the UFO lighting. I posted some photos a while back on how I did it.
https://pinside.com/pinball/forum/topic/stern-godzilla-official-owners-club/page/161#post-6797673
You're currently viewing posts by Pinsider Selig.
Click here to go back to viewing the entire thread.
Wanna join the discussion? Please sign in to reply to this topic.
Great to see you're enjoying Pinside! Did you know Pinside is able to run without any 3rd-party banners or ads, thanks to the support from our visitors? Please consider a donation to Pinside and get anext to your username to show for it! Or better yet, subscribe to Pinside+!
This page was printed from https://pinside.com/pinball/forum/topic/stern-godzilla-official-owners-club?tu=Selig and we tried optimising it for printing. Some page elements may have been deliberately hidden.
Scan the QR code on the left to jump to the URL this document was printed from.