(Topic ID: 219896)

Stargate Flippers problem


By scottnds

1 year ago



Topic Stats

  • 5 posts
  • 2 Pinsiders participating
  • Latest reply 1 year ago by scottnds
  • No one calls this topic a favorite

You

Linked Games

No games have been linked to this topic.

    Topic Gallery

    There have been 2 images uploaded to this topic. (View topic image gallery).

    20180625_202445 (resized).jpg
    Screenshot_20180625-202134 (resized).png

    #1 1 year ago

    Hi.
    I am having trouble with my Stargate. After a long time I had a game on my Stargate and the skill shot in the Sarcofagus was not registering. I cleaned the contacts on the roll over switch in the sarcofagus and it worked 50% but then the 2 bottom flippers now do not work.The top flipper works and the 2 bottom flippers move slightly about 1-2 mm.
    Can anyone point me in the right direction to fix this.
    Thanks
    Scott

    #2 1 year ago

    Try to move it by handle to check mecanism, but if both move slowly probably due to electronic component...on A15 board or low voltage somewhere.

    Look at electrical diagram on the web by searching stargate.pdf and check voltage.
    Couldn't help you more for the moment.

    20180625_202445 (resized).jpgScreenshot_20180625-202134 (resized).png
    #3 1 year ago

    Thanks.
    I have just had a play with it and the flippers were the same so I moved them into the hold position a couple of times with the flipper buttons pressed and now they are working. And the sarcofagus is working again also.Is there anything I should be checking for?Thanks for your help.

    #4 1 year ago

    You may check the glider craft motor under the playfield...if there's much clearance at the axle you might put a 8A fuse just back of the motor until you will burn the electronic card fix on it or change the motor.
    Also shunt all ground wires near the tranformator as it is required on pinrepair.com (Gottlieb SYSTEM 3)
    Until you might burn transistor on A3 card board if there's a bad connection.

    Good luck

    #5 1 year ago

    Thanks Benhurr. I have done the ground wire fix a couple of years ago. I will check the other stuff also.Thanks for taking the time to help.
    Cheers
    Scott

    Promoted items from the Pinside Marketplace
    From: $ 42.00
    Cabinet - Shooter Rods
    ModFather Pinball Mods
    $ 29.50
    Playfield - Plastics
    Pinball Haus
    $ 48.00
    Cabinet - Other
    ModFather Pinball Mods
    From: $ 9.99
    Eproms
    Matt's Basement Arcade
    $ 24.25
    Playfield - Toys/Add-ons
    The MOD Couple
    $ 69.95
    Playfield - Toys/Add-ons
    Hookedonpinball.com
    $ 75.00
    Gameroom - Decorations
    The Pinball Vault
    $ 50.00
    From: $ 15.00
    Electronics
    nvram.weebly.com
    From: $ 35.00
    Boards
    PCB Emporium
    $ 95.00
    Playfield - Toys/Add-ons
    M&M Mods
    From: $ 5,899.99
    $ 7,599.00
    Pinball Machine
    Operation Pinball
    $ 229.99
    Lighting - Other
    Lighted Pinball Mods
    $ 48.00
    Cabinet - Other
    ModFather Pinball Mods
    From: $ 3.00
    Lighting - Interactive
    Professor Pinball
    $ 399.99
    Cabinet - Toppers
    Great American Pinball
    From: $ 42.00
    Cabinet - Shooter Rods
    ModFather Pinball Mods
    $ 5,599.00
    Pinball Machine
    Ghostbusters Pro Out of stock
    Operation Pinball
    $ 154.00
    Cabinet - Toppers
    Id Rather Play Pinball
    From: $ 5,899.95
    Pinball Machine
    Pinball Pro
    $ 219.00
    Cabinet - Toppers
    Id Rather Play Pinball
    From: $ 9.99
    Eproms
    Matt's Basement Arcade
    $ 14.95

    Hey there! Got a moment?

    Great to see you're enjoying Pinside! Did you know Pinside is able to run thanks to donations from our visitors? Please donate to Pinside, support the site and get anext to your username to show for it! Donate to Pinside