Just picked up a Spy Hunter. It’s been sitting for several years. No power to anything except the GI lights in the head. All fuses are good. Tried resetting all plugs. Any help on where to start from here

No lights at all. No power to boards. The transformer is putting out the correct voltage. Just replaced the power module. I has the original battery. Not sure if that would be it.

I’m getting nothing on those up or down the pin accept for number 6 counting from top down. 4.5

I installed a new Ultimate power module yesterday from Marco.

That’s the one I replaced

4A33AD69-3BE9-4F4E-BC1A-7C8928EC26F6 (resized).jpeg

I checked the voltage all the way to the solenoid driver all test well. I bought a new Solenoid driver board. We will see.

I thought my voltages were good but after installing my new solenoid driver board following the new rectifier board. I don’t have 12 or 5 volts on the driver board. And no dcv voltage on the rectifier. I do have the correct voltage on the acv. I do have 43 vdc and 180 vdc only on driver nothing else. No power to mpu. I tested J5 and J6 plugs from transformer. All volts are correct on J5, J6 I tested pin 3 to 6 and got 9.5 volts but 1 to 5, or any other combo for that matter, nothing. Could it be the transformer?

All the wires are all in their original loops and is un hacked. I bought this from a family who had it for the last 30 years. However it was in the garage. Does smell musty.

20AA05C5-126D-4B07-BBFD-7A5D0121A4F1 (resized).jpeg

7E0CB373-BFB1-4ABE-B687-3750E8AE746A (resized).jpeg

861B293B-FFCD-4303-93F1-27EE2C9D3209 (resized).jpeg

B201209E-1C6E-47F9-87E8-C34F2797A02C (resized).jpeg

B745ECF7-87F4-4BDE-8DCE-B99C6534F0EF (resized).jpeg

C459B43D-6AC8-4C13-9F25-BED0199C31A0 (resized).jpeg

Everything looks as it should. All plug in well. Just don’t know.

4F83055B-CC5F-43D6-973E-4617246A6524 (resized).jpeg

D4371240-0EBD-467B-8AD3-FF4FEDF35915 (resized).jpeg

44D1EB21-3133-4270-994B-9A106AFD4919 (resized).jpeg

F0CEA09E-EDF0-43F0-B647-50C190E7A898 (resized).jpeg

ABACC7FA-7DBE-4F25-B2FE-172556033E51 (resized).jpeg

7457A651-1A03-4C86-BFA0-33C9F59F0868 (resized).jpeg

BA8385A0-FCC6-4EA8-A61E-27C7423CC519 (resized).jpeg

Sorry some pics loaded sideways

All plugs are pushed in and making contact. I’ll check that continuity next

Yes I have continuity on those.

Yes there is continuity between those two points

Zero

Nope I only have new pins. I just got this solenoid board from Marco today. I installed it and no change at all from old. I re installed the old one with no change either. This is crazy. I’ll reach out to pnw pinball collectors if anybody can help with board swaps. I owned and sold a SH last year. I am have an opportunity to buy it back. I have a half a mind to buy it to try to solve this problem. In the mean time I’ll keep on this and post if I find the issue.

I’ve done that already. I get 14.2 volts but nothing at Tp3

I just realized yes I just put the new rectifier is brand new but it keeps blowing f3 4 amp fuse. Not sure where to go from here.

Let me go back to the original rectifier board. It had a power wire soldered from Tp1. Maybe someone can make sense of it.

77B6EB81-FADA-4ED6-AF37-74D69B928F81 (resized).jpeg

Update. I did a process of elimination. I bought 20 4 volt fuses. I unplugged everything except J6 and turned on the game, of course fuse didn’t blow. I turned it off and plugged the rest of the rectifier plugs one by one, good so far. I plugged in J3 and turned on. Lights came on on the solenoid board. I repeated this process through the solenoid board with no issues. I next plugged in J1 in the sound board and fuse blew. I unplugged it and plugged in everything else. The MPU light it solid no flashes. I slowly plugged in J1 again and looking closely pin 10 sparks and fuse blows. Orange wire with yellow trace. Pulled play field and eliminate that. Unplugged coin door still lights on. Can’t find any grounded wires.

Also the displays are not turning on.