(Topic ID: 65459)
Topic Stats
- 851 posts
- 232 Pinsiders participating
- Latest reply 77 days ago by SYS6
- Topic is favorited by 305 Pinsiders
- Topic is sticky in its sub-forum
You
- You are not signed in!
Full Topic Index (key posts)
51 key posts have been marked in this topic.
Display key post list sorted by: Post date | Keypost summary | User name
Post #251 6vdc portable bulb tester (555 wedge, 44/47 socket and comet matrix lighting), led lit mod tester and great for comparing 2 x leds or bulbs next to each other for the 44/47's and lastly a torch/flashlight. Posted by swinks (7 years ago)
Post #75 Backboard stand & X+Y-axis motorcontrol" for Johnny Mnemonic. Posted by zaza (10 years ago)
Post #242 Bally display tester, Gottlieb driverboard tester, Atari Gen 1 cpu board tester. Posted by MarAlb (7 years ago)
Post #121 Bally or Stern lamp driver test pcb. Posted by barakandl (9 years ago)
Post #249 Bally/Stern lamp driver tester and a Solenoid drive tester based on a write up from Leon Borre. Posted by Billc479 (7 years ago)
Post #2 Block shooter lane to raise the playfield without removing your balls. Posted by mof (10 years ago)
Post #81 Board made to work with Andre's test ROM for WMS 3-7 MPUs and driver boards. It connects to a display plug and gives a bally like POST flash sequence which helps speed up board repair. Posted by barakandl (9 years ago)
Post #44 Bulb removal / insertion tool & tool for tightening / removing the sleeves that the playfield sits on in games like TAF. Posted by Vector (10 years ago)
Post #99 Bulb remover. Posted by rollinover (9 years ago)
Post #70 Clay's LED tester in a pen case. Posted by SchertzPinball (10 years ago)
Post #831 coil sleeve remover Posted by MarkG (1 year ago)
Post #118 Cord for powering up Bally transformers and rectifier boards without a machine. Posted by PghPinballRescue (9 years ago)
Post #123 DIY "hex screw contact hubs." Or if you prefer the commercial version, solder lug connectors - http://www.digikey.com/product-detail/en/7327/7327K-ND/316696 Posted by mof (9 years ago)
Post #106 Drill depth stop using a cork. Posted by Cheddar (9 years ago)
Post #8 Gritgetter holds a rag with Novus to remove ball trails in hard to reach places. Posted by tracelifter (10 years ago)
Post #61 Helping hands type unit. Link to eBay store. Posted by pinball_faz (10 years ago)
Post #31 Inexpensive pinball dolly. Two wheels, a handle, and some scrap 2x4. Posted by SchertzPinball (10 years ago)
Post #116 Jig for making Black Hole upkicker tubes. Posted by blownfuse (9 years ago)
Post #89 JohnWartJr chimes in on additional uses for a benchtop power supply. Posted by johnwartjr (9 years ago)
Post #3 Light bulb remover. Posted by mof (10 years ago)
Post #122 Link to color matching formula spreadsheet. Posted by Curbfeeler (9 years ago)
Post #16 Link to homemade CNC router. Posted by vid1900 (10 years ago)
Post #26 Link to pinball dolly using an ATV/motorcycle lift as a starting point. Posted by JeffZee (10 years ago)
Post #20 Lock picks and tension wrench. Posted by Fanatic (10 years ago)
Post #119 Marco third hand with magnet attached. Posted by dtown (9 years ago)
Post #120 Marked string for determining the correct size rubber. Posted by jeffc (9 years ago)
Post #125 More info on the roll pin remover. Posted by Pinthetic (9 years ago)
Post #136 PCB holders for securing it up off the bench high enough for soldering. Posted by mhkohne (9 years ago)
Post #92 Pin set up assistant. Posted by Rickwh (9 years ago)
Post #155 Playfield support blocks. Posted by JeffZee (8 years ago)
Post #103 Portable bench test kit for Bally -35. Posted by KenH (9 years ago)
Post #49 Post removal and installation. Posted by Superchicken (10 years ago)
Post #71 Post sleeve maker. Posted by LTG (10 years ago)
Post #198 Post spinner device, coil shank, and contact cleaner. Posted by balzofsteel (8 years ago)
Post #84 Power supply for 5v, 12v, -12v and ground. Direct fit for Williams, other pigtails made as needed. Posted by HHaase (9 years ago)
Post #24 Raised playfield stabilizer. Posted by mof (10 years ago)
Post #47 Re-graining metal rails and fences. Posted by Vector (10 years ago)
Post #101 Removable work table for soldering. Posted by Skypilot (9 years ago)
Post #21 Roll pin remover. Posted by KenH (10 years ago)
Post #206 Rolling tray table has many uses. Posted by cottonm4 (8 years ago)
Post #109 Rotisserie mod for System 11. Posted by Whysnow (9 years ago)
Post #196 Solder station shelf. Posted by JeffZee (8 years ago)
Post #28 Soldering platform. Posted by OuttaSpace (10 years ago)
Post #79 Solenoid tester for WMS 3-7 games. Posted by barakandl (9 years ago)
Post #72 System 11 playfield holder. Posted by Taxman (10 years ago)
Post #135 The Pin Pan, platform for soldering iron and other tools. Posted by swampfire (9 years ago)
Post #52 Tumbler media sifter/storage bin. Posted by Superchicken (10 years ago)
Post #114 Washer & string help pull socket legs while desoldering. Posted by sixpakmopar (9 years ago)
Post #117 Wireform rail stamp for making splined ends. Posted by blownfuse (9 years ago)
Post #253 Yet another solder station shelf. Posted by WJxxxx (7 years ago)
Post #39 YouTube video of portable pinball LED and lamp tester. Posted by Eddie (10 years ago)
Showing the full topic Key Post index. Click here to go back to the forum thread.
This page was printed from https://pinside.com/pinball/forum/topic/show-and-tell-your-diy-homemade-tools/page/11?kp=1&kp_sort=keypost_summary and we tried optimising it for printing. Some page elements may have been deliberately hidden.
Scan the QR code on the left to jump to the URL this document was printed from.