Quoted from SUPERBEE:Same here. Any suggestions on how ? Dont think you can buy a big clear bucket.
An old 5 gallon fish tank?
You're currently viewing posts by Pinsider vid1900.
Click here to go back to viewing the entire thread.
Quoted from SUPERBEE:Same here. Any suggestions on how ? Dont think you can buy a big clear bucket.
An old 5 gallon fish tank?
They sell 40% peroxide at the beauty supply house that is paste.
I wonder if you mixed the oxy with it and just put the paste on the face of the plastic - keeping it away from the backside?
I wonder if the type of plastic makes a difference.
You know how those old Bally plastics stink like cheese?
The Frisket used to mask while painting is solvent resistant (it does not lift, wrinkle or allow paint to creep under it).
Maybe that could protect the screen printed side of the plastics while soaking?
I tried this, using frisket to mask the paint on the back of the plastics.
The plastics were cleaned with Novus2 to get any surface gunk off, so the peroxide could work and not get blocked by waxes or nicotine.
I found 2 piss yellow plastics of the same year (1978). These are the plastics that smell like puke.
I used 1/4 teaspoon of Oxy-Clean to 1/4 cup BRAND NEW 3% Hydrogen Peroxide. If your peroxide has been opened for a few weeks in the closet, it's not 3% anymore.
I put the mix in a ziplock bag, then put the bag in a shiny aluminum pie pan on my hotel balcony in the morning.
sbm-before.jpgQuoted from jwilson:Maybe a couple of layers of frisket?
No, the frisket glue did not hold at all.
The frisket film turned white and was just floating around in the mix.
Quoted from OLDPINGUY:I might suggest trying wax/Paraffin. It will come off in hot water, but should be easy to coat.....
How hot of water?
I wonder if the chemical reaction or the sunlight will make it too warm?
Quoted from ddebuss:Why not skip the oxyclean altogether. If I remember the thread right all the plastics that had paint come off also had oxyclean as well. Does the peroxide by itself take the paint off?
Oxyclean has the necessary Tetra Acetyl Ethylene Diamine we need to start the reaction.
Quoted from VacFink:Is it outdoors? And if so for how long?
It was cloudy this morning, so I put them out at lunchtime and came back to get them after sundown. So it might have been 7 hours.
Quoted from VacFink:They seem to still be a bit yellow.
You can't see the yellow when you hold them in the air, but you can see it when you put them on bright white paper.
I'd say 80% of the yellow is removed.
If it's sunny in the morning, I might put them out for another round with fresh chem.
I'll report if any further de-yellowing occurs.
Quoted from VacFink:two 75W UV bulbs to see how well it works controlled indoors.
UV A or B?
Quoted from VacFink:Vid did the plastics smell any better after the treatment?
I did not smell them yet.
I was going to run them one more time, but it's been raining.
Quoted from Riptor:Has anyone tried this in an eprom eraser to speed up the process?
Or if you have a stripper girl friend, she could take them in the tanning bed for you.
Quoted from Gerry:But she works in an office, and not on the pole
I would not doubt she works the poles in the office.
Quoted from Eddie:Will have to try frog tape next time as the blue painters mask didn't do its job.
Try real painter's frisket like the stuff from TCP Global.
That stuff does not bleed at all.
You're currently viewing posts by Pinsider vid1900.
Click here to go back to viewing the entire thread.
Wanna join the discussion? Please sign in to reply to this topic.
Great to see you're enjoying Pinside! Did you know Pinside is able to run without any 3rd-party banners or ads, thanks to the support from our visitors? Please consider a donation to Pinside and get anext to your username to show for it! Or better yet, subscribe to Pinside+!
This page was printed from https://pinside.com/pinball/forum/topic/say-goodbye-to-old-yellowed-plastics?tu=vid1900 and we tried optimising it for printing. Some page elements may have been deliberately hidden.
Scan the QR code on the left to jump to the URL this document was printed from.