Chester, MD
One of the bugs that drives me nuts is when your in radio riot 2 ball and you lose one, you never get it back. Even when shoot again is flashing. Anyone else have this?
(Topic ID: 83745)
Linked Games
Road Show
Williams, 1994
Topic Gallery
You're currently viewing posts by Pinsider MikeSinMD.
Click here to go back to viewing the entire thread.
8 months later
4 months later
Quoted from BryanD:Need some guidance with Ted. His mouth won't open. In test, I can open the mouth manually, and it will close ok. I can switch Red and Ted connectors on the Dual H Drive Controller and Ted works fine- so I don't think it is the motor/ binding/ gears/ missing teeth. The Drive Controller has had Q6 replaced, which fixed a slack jawed Ted (lazy movement). This was awhile ago, I don't think it led to the current problem.
The manual has Solenoid 19 for Ted's motor direction, but 19 does not show up in the test menu. One chart in the manual (page 2-48) shows the J117 connector for the drive direction, and another chart (inside front cover and page 3-5) the J118 connector. J126 connects the Dual H Drive Controller to the board. These have been reseated, and show no burn marks.
I did LED most everything, replaced the start button, and replaced fuse F106 just prior, but Ted worked fine for a good hour or two afterwards. Appreciate any help.
I had similar issues. Sent the dual motor board to Chris Hibler for repairs. Everything works as it should now.
3 weeks later
Quoted from kdunbar:The biggest problem I had were the Eddy sensor boards, I replaced them with auto adjusting ones and haven’t had a problem since
Which ones did you get?
1 month later
Quoted from TomT:I don't see a flasher listed for the ball lock in the manual?
Top left, right where the ball comes out from the lock. Flashes when ball comes out of there.
Quoted from TomT:I'm guessing #38? It's the only flasher in that area other than the back panel flashers.
[quoted image]
Maybe. Look at the pic in the post above mine. It’s a yellow flasher just behind the lite radio riot sign. I’m not near the machine right now but will be later. Thanks
2 months later
Quoted from monkfe:Well I'm in for a set if anyones does a group buy
Me too!
1 year later
Quoted from Davi:There are 4 wire ramp assy:
A-18506 Left wire shooter ramp assy
A-18507 Left wire ramp assy
A-18508 X-over wire ramp assy
A-18509 Right wire ramp assy
Where is the nut/bolt you are looking for?
OK. I should have been more specific. It is Almost in the center of the play field. It is where the left side crosses over and connects to the right wire ramp. Thanks
11 months later
11 months later
Quoted from allsportdvd:Bought a new set of plastics and not sure where this one goes?
Anyone know?
[quoted image]
Good question! I want to know also, because I don’t see it anywhere on mine. Mìke
Quoted from Oscope:Could this be it - both have two screw holes between Red and Ted?
The left side does not have the corner taper
[quoted image]
I think these are some kind of mod. My game doesn’t have these either.
Promoted items from Pinside Marketplace and Pinside Shops!
You're currently viewing posts by Pinsider MikeSinMD.
Click here to go back to viewing the entire thread.
Reply
Wanna join the discussion? Please sign in to reply to this topic.
Hey there! Welcome to Pinside!
Donate to PinsideGreat to see you're enjoying Pinside! Did you know Pinside is able to run without any 3rd-party banners or ads, thanks to the support from our visitors? Please consider a donation to Pinside and get anext to your username to show for it! Or better yet, subscribe to Pinside+!
