(Topic ID: 218168)
Linked Games
Bad Cats
Williams, 1989-
Black Knight
Williams, 1980
-
Blackout
Williams, 1980
-
Comet
Williams, 1985
-
Eight Ball Deluxe
Bally, 1981
-
Evel Knievel
Bally, 1977
-
Fireball II
Bally, 1981
-
Firepower
Williams, 1980
There are more than 8 games linked to this topic.
Click here to show all linked games
Click here to show all linked games
Topic Gallery
You're currently viewing posts by Pinsider a1k71.
Click here to go back to viewing the entire thread.
Macomb, MI
I was able to reuse the original inserts and no black marker was needed around the inserts outline.
So I think it all depends on the conditions of the inserts
20220201_115158 (resized).jpg20220201_120352 (resized).jpg20220202_005244 (resized).jpgreceived_1014399245901711 (resized).jpegreceived_481430503609603 (resized).jpegreceived_949211292653010 (resized).jpeg
I got those from eBay
ebay.com link: itm
I am looking for the one to put on top of the clear plastics (from the plunger lane and the divert cover)
Quoted from ibis:Start from the bottom up, not the top down. That way if there's a slight off-set, its out of the eyes view.
I didn't have to do that, the alignment was precisely done, put it firmly taped on the bottom part and result was perfect.
Also with gates, spinner, posts, metal rails guides etc. you need a perfect alignment on the top part too.
It just take few extra minutes to carefully put it on place.
At the end the 95-97% of all the holes where perfectly in place, just 2 or 3 needed to be enlarged a little bit
7 months later
Quoted from Robotworkshop:Here is a thread that covers those small rollover buttons and replacements that are available in different colors:
https://pinside.com/pinball/forum/topic/c-587-6-bally-rollover-buttons-now-available-for-xenon-and-kos
It's not matter of buying smaller rollover buttons.
The holes are not aligned at all
Quoted from Robotworkshop:Here is a thread that covers those small rollover buttons and replacements that are available in different colors:
https://pinside.com/pinball/forum/topic/c-587-6-bally-rollover-buttons-now-available-for-xenon-and-kos
I think the holes on the hardtop are not aligned correctly . Are also (I want to say) half of the size that they suppose to be, accordingly on the playfiled original holes.
I think I need to "drill" them all (in some way) to match the playfiled holes.
I will read that post, but I think even smaller buttons will not.fit at the moment.
Correct holes size should be like the ones in this picture
Screenshot_20220929_035249_Chrome (resized).jpgQuoted from Robotworkshop:No, I just posted that in case you need new ones or wanted ones in a different color. I believe all of the small rollovers are the same size.
There are variations in the playfields so some holes are made smaller on purpose. Those are meant to be enlarged later once the hardtop is attached. May be able to carefully use a step drill, regular drill, dremel with appropriate cutter, or a small router bit.
Got it. I misunderstood.
Thank you for the explanation and the link. I'll dig into it.
Maybe a different color buttons will look good
Promoted items from Pinside Marketplace and Pinside Shops!
Coffs Harbour, NS
You're currently viewing posts by Pinsider a1k71.
Click here to go back to viewing the entire thread.
Reply
Wanna join the discussion? Please sign in to reply to this topic.
Hey there! Welcome to Pinside!
Donate to PinsideGreat to see you're enjoying Pinside! Did you know Pinside is able to run without any 3rd-party banners or ads, thanks to the support from our visitors? Please consider a donation to Pinside and get anext to your username to show for it! Or better yet, subscribe to Pinside+!
