I’ve just joined the club! Going to do a full restoration on it and have all the parts located apart from a new plastic set. Does anyone have any leads?
You're currently viewing posts by Pinsider allsportdvd.
Click here to go back to viewing the entire thread.
I’ve just joined the club! Going to do a full restoration on it and have all the parts located apart from a new plastic set. Does anyone have any leads?
Quoted from mollyspub:[quoted image][quoted image][quoted image]
New plastic set, ramps = new high score!
New translite too? Where did that come from?
Do owners here have a Center post between the flippers on their game?
Mine has a plastic stopper in it
I’d look through the topic gallery but it seems to be gone on the new pinside?
Quoted from mollyspub:Black Powercoated armor When changing these over , it confirmed what I already knew. This game has not been redecaled !
[quoted image]
Fantastic, where did you get the apron cover? I want one of those!
Quick question while I’m restoring my game. When the skydive drop target comes down it is suppose to be flush with the playfield or sit slightly above. Mine sits slightly above that level in dropped position
Quoted from PoMC:My latest mod turned out so spectacular that I’ve decided to make it available to purchase.
$69 shipped to anywhere in the USA.
[quoted image]
Shipping option to Australia?
Quoted from PoMC:I was making a joke about selling the mod. LOL.
It’s literally two googly eyes taped to the skull. I did it as a joke just to amuse me and make my wife laugh.
But it actually looks pretty bad ass I think.
Oh right, stupid me for thinking it was something different now I'm looking somewhere other than my phone lol
Well here I am again. Not sure anyone reads this thread lol
My restoration is finished, only issue is the auto plunger get stuck in the up position
here are some pics.
Question. When is the jump ramp available to shoot vs the magnet holding the ball and sending down the left wire form?
I seem to get rejections all the time but tested the magnets and they seem to work fine
Some more help please. My ball popper VUK will not shoot a ball up if there are 2 or more balls in the subway. It tries a few times but then stops making Multiball useless
Here is a pic of the vuk, is there anything missing or is that the correct sleeve?
Quoted from GRUMPY:Fix this bad connection too. Coil power comes from high current flow, 3-4 strands of wire isn't good for flow.
[quoted image]
Good tip! I’ll do that cheers!
Hi all
I was in the middle of a good game (always the way) and every single solenoid stopped working
I’ve checked fuses 105, 112, 115, 116 and all those are fine
Any ideas?
Quoted from DK:Check the service switch on the coin door
You mean the buttons inside the coin door? All 4 buttons on the door working fine
Aah I get the warning the the high voltage is cut off when I open the door so I assume it’s fine. Pressing and letting go of the button does the same
Quoted from topkat:Here’s a view
[quoted image][quoted image]
You have a lightning flipper in there that is 1/4” shorter. That’ll certainly make your sweet spot smaller
I just assumed it was the shorter one as I'm pretty sure all the lightning bolt ones are shorter, can't tell by the pic but also haven't seen a long shaft lightning flipper before. Also haven't seen the long shaft in any colour other than yellow which is a shame as I'd like to have a different colour in mine
Quoted from smcclain65:Joined the club last thursday, having a blast and had a few billion plus games. I ordered a Colo DMD and was wondering what were the must have mods.
1. Die cast valvoline car looks pretty standard, Can someone show me pics of how they attached?
2. Motocross rider, same as above can someone show pics and which model/toy?
3. Upgraded speakers and pinsound. Has anyone done this and have a gameplay video?
Thank you all.
I have a 1:43 scale Valvoline car and mounted it here below
I’d like to see a bike too actually
I turned the staged ball setting off too, however I did mine because every time there are 2 balls in the subway, the popper has a real problem shooting one out. It’s a problem during Multiball in particular, it takes quite a few attempts to get it cleared.
The popper is nice and tightly screwed in. Any ideas?
Quoted from Paulb:anyone know where this piece goes in the game ??
hard to see put its clear plastic, not the part the clips on to the metal ramp, Ive looked thru a bunch of pics ?[quoted image]
Those clear plastic strips attach to the backboard and bend down towards the side rails, like this
5597A604-D3D4-4321-8F71-9EF7B3429933 (resized).jpegI recently restored mine and didn’t put that part under the new ramp
I would assume for home use it isnt necessary
Quoted from mollyspub:Wonder where you got that idea from…
[quoted image][quoted image]
Don’t know what you’re talking about, my design is completely different
Quoted from ClassicHornet:He said “idea” not design, both look amazing imo
All good I was being sarcastic lol but my smiley face emojis didn’t show!
Quoted from Kawydud:New translite came in the other day, got to install it last night. Looks great![quoted image]
That does look pretty good, where is it sold?
You're currently viewing posts by Pinsider allsportdvd.
Click here to go back to viewing the entire thread.
Wanna join the discussion? Please sign in to reply to this topic.
Great to see you're enjoying Pinside! Did you know Pinside is able to run without any 3rd-party banners or ads, thanks to the support from our visitors? Please consider a donation to Pinside and get anext to your username to show for it! Or better yet, subscribe to Pinside+!
This page was printed from https://pinside.com/pinball/forum/topic/no-fear-club-play-better?tu=allsportdvd and we tried optimising it for printing. Some page elements may have been deliberately hidden.
Scan the QR code on the left to jump to the URL this document was printed from.