What are you using for that NBA logo light?
Car door light?
(Topic ID: 153483)
Linked Games
NBA Fastbreak
Bally, 1997
Topic Gallery
You're currently viewing posts by Pinsider J-Freeze.
Click here to go back to viewing the entire thread.
1 week later
4 months later
3 months later
2 weeks later
Quoted from Don44:I got the piece https://www.marcospecialties.com/pinball-parts/04-10253 to hold on the blue pad and I got it on there but it was a little bit too tall for the hole to line up perfectly so I had to put another washer underneath the metal lane guide to make it a little taller. I attached it with a 4-40-3/8 screw. Anybody else have this problem?
Yeah mine was too tall as well, I filed about an 1/8" off but I like your solution better haha.
I moved mine with the test in the menu.
Moving it by hand could break it, or at least make it not recognize where it is.
1 month later
Quoted from AFM95:I just want to say that I miss being in this club! Such a fun game.
Ditto!
5 months later
Quoted from garretswinning:Could somebody shed some light on how this plastic attaches with a pic[quoted image]
I think that's just a keychain.
2 months later
Quoted from ScottyC:LCD for deeper blacks (IMO) and consistent colors from all angles. LED version you still see the LEDs which are off (unless you add a film over the screen), and at an angle you can see separation in the LED colors a bit(IE for purple you can see the individual red and blue LEDs). Gonna have to see if LCD is a confirmed fit in this machine before I order though
The LED version is the one with deeper blacks and better viewing angles.
LCD has more options as far as dots and smoothing.
4 months later
Quoted from dayrover:Just finished putting a LED ColorDMD in my Fastbreak. Looks great!
I could do with the clubs help on one issue with my machine. The high power coils tend buzz loudly when they are held on. This is particularly noticeable with the left loop diverter, but loop gate and right loop diverter buzz too.
I guessing this is because the 50V solenoid power is not very well smoothed. My question is this normal?? The 50V solenoid is only smoothed with a small 100uF capacitor. This does not seem a lot for these large coils! Before I start replacing capacitor or rectification diodes I am wondering whether they are in fact at fault or just the physical design of the left loop diverter mean the buzz is easily heard.
What do you all think?
Quoted from chuckwurt:My game does the same thing. No idea If it’s normal.
Sounds crazy but it works,
Replace the coil retaining bracket.
Or swap it with one from the passing coils (they dont get held on as long so they wont hum)
https://www.pinballlife.com/coil-retaining-bracket.html
Quoted from Y3AG3R:Buzzing is just a sign of wear. Most of the time it is the plunger mushrooming I think vid talks about in his flipper guide.
The plunger base?
It is a diverter, not a normal plunger.
The base either bends the retainer or wears enough of a ring in the retainer due to being held in that position and vibrating to cause the hum.
2 weeks later
Circled in orange is a curve in the launch that would prevent the ball going up the right ramp.
Circled in green are the pop bumpers, red x is the one I think you are referring to (you probably know this but your arrow made it confusing)
Blue lines are just hair for the green pop bumper man.
Do you know what is wrong with the pop bumper, did the seller tell you?
You may not have to take the ramp off, it may (most likely) be able to be repaired from underneath.
20200627_012157 (resized).jpgQuoted from marioparty34:I would say I get blocked about 25%... Not a good feeling.
On a side note, putting my initials for the Bulls has become my life mission. I just can't make it to the third ring!
I dont think it's possible, I'm pretty sure that it won't let you play for a third ring with the bulls.
Quoted from GroundControl:How could that be?
It would be like an easter egg from an ostrich.
I guess because it was made in Chicago...
https://pinside.com/pinball/forum/topic/nba-fastbreak-rigged#post-2784947
10 months later
Quoted from rockwell:Great, yes that does help clarify, thank you. I did find the images from the other post in this thread. I will definitely have to grind a little bit off of the bottom to make it fit. But otherwise should be good! Cheers.
I had to file some off the bottom of mine.
Promoted items from Pinside Marketplace and Pinside Shops!
West Chicago, IL
You're currently viewing posts by Pinsider J-Freeze.
Click here to go back to viewing the entire thread.
Reply
Wanna join the discussion? Please sign in to reply to this topic.
Hey there! Welcome to Pinside!
Donate to PinsideGreat to see you're enjoying Pinside! Did you know Pinside is able to run without any 3rd-party banners or ads, thanks to the support from our visitors? Please consider a donation to Pinside and get anext to your username to show for it! Or better yet, subscribe to Pinside+!
