Quoted from Leo13:I was wondering how to access special settings menu, thanks a lot !
The four diagnostic buttons on the coin door. Please hold the "Escape" button down for 5 seconds or so.
LTG : )
You're currently viewing posts by Pinsider LTG.
Click here to go back to viewing the entire thread.
Quoted from Leo13:I was wondering how to access special settings menu, thanks a lot !
The four diagnostic buttons on the coin door. Please hold the "Escape" button down for 5 seconds or so.
LTG : )
Quoted from stangbat:Put my game on location this afternoon. 3 hours later, the display is dead. It earned a whopping $2 before breaking. Awesome.
Please reseat the hdmi connector on top of the board in the head.
LTG : )
Quoted from stangbat:Opened a ticket with more details.
I added a note on there for Doug to look into it.
LTG : )
Quoted from stangbat:Sorry for my snarky prior post, but I'm rather bummed.
No problem. Crap happens. And when you are the one it happens to, it is unfortunate.
They will get you going. I'm sure the engineer will be sending a new board, from the sound of your issue and what you have done/checked so far.
LTG : )
Quoted from EricR:Is there an email address he can contact directly?
Always best to open a ticket on the help desk.
LTG : )
Please check the LCD over to see if there are any controls on it.
If not, I'd try a factory reset next.
And open a ticket on the help desk.
LTG : )
Unplug the power to the LCD, and leave it sit for a few minutes. Then plug it back in and turn the game on. See if that does it.
LTG : )
Quoted from LP30:but the main controller board
I updated your ticket so CGC can get you what you need.
LTG : )
Quoted from MrSanRamon:Does everyone's outlet look like this:
From about AFM on, every Williams game had that for a service outlet. Same with MMr.
Any computer store should have a cord you can plug into it with a normal female plug on the other end.
LTG : )
Quoted from LP30:I'll have to follow-up with CGC again to see why I never heard anything else from them.
Please pm me the ticket number and I'll look into it.
LTG : )
Quoted from MrSanRamon:I just let the plunged balls take whatever route they would naturally take without any shaking of the machine, and on mine 75% plus hit the right sling.
Loosen the kicker assembly and turn it a little to aim the ball different.
LTG : )
Quoted from MrSanRamon:Not sure what you're saying...do you mean loosen the sling mechanism and rotate it?
No, the plunger assembly that launches the ball into play up the shooter lane.
LTG : )™
Quoted from northvibe:ANd my left troll head wont register a hit, if you pull the face forward and let go it does, so a small adjustment butttt what is the best way to get to that switch.
I've pulled the whole assembly up. Put a small vice grips on the carriage wall so it doesn't go back down. Then adjust the leaf blade. It's a simple leaf blade switch. Troll face on the long front one. Short rear one behind it. Adjust the rear one.
You can unplug the troll face switch, remove the bolt thing holding the carriage to the plunger, and pull the whole assembly up and out. Lean to the left to clear the playfield.
LTG : )
Quoted from mcbPalisade:Is there a way to remove Service Credits if you accidentally add to many?
Go into Williams Main Menu - Utilities - Remove Credit - hit Enter then hit Start button to do it. All gone.
LTG : )
Quoted from Ilushka85:On the right side there is a red flasher and just above it there is an led flashed under the plastic. Is that led supposed to have a cover of some sort ? It’s super bright white and uncovered. Doesn’t seem right.
Do you mean under the plastic behind the three red stand up targets on the right side ? If so, no cover under there.
LTG : )
Quoted from Ilushka85:Talking about the hole under the bracket here
Okay, now I can see and check the area.
No cover.
You could add one if you like.
LTG : )
Quoted from Ilushka85:Am I just crazy that it’s the only bright white led that’s visible in the game ?
I wouldn't call you crazy. You might just be the right height that it bothers you. I'd invent a cover for it.
LTG : )
You're currently viewing posts by Pinsider LTG.
Click here to go back to viewing the entire thread.
Wanna join the discussion? Please sign in to reply to this topic.
Great to see you're enjoying Pinside! Did you know Pinside is able to run without any 3rd-party banners or ads, thanks to the support from our visitors? Please consider a donation to Pinside and get anext to your username to show for it! Or better yet, subscribe to Pinside+!
This page was printed from https://pinside.com/pinball/forum/topic/mmr-owners-thread?tu=LTG and we tried optimising it for printing. Some page elements may have been deliberately hidden.
Scan the QR code on the left to jump to the URL this document was printed from.