Lost World
Bally, 1978You're currently viewing posts by Pinsider Knxwledge.
Click here to go back to viewing the entire thread.
I bought a Lost World, and the power switch was missing. I've attempted twice now to wire it and very clearly I don't know what I'm doing. Am I using the right type of switch? Any help appreciated. Attached down below is schematics, along with the first attempt I made at wiring it up (which lead to smoke coming off the butt connected wires of the load side of the line filter lol).
20201028_190150 (resized).jpg20201028_194629 (resized).jpg20201028_194633 (resized).jpgQuoted from LTG:Does vid's guide help any ?
https://pinside.com/pinball/forum/topic/replacing-line-cords-plugs-wall-sockets-vids-guide
LTG : )
This is for wall plugs, which I believe I have wired in correctly (I bought a whole new cord, and I just soldered ground, hot and neutral onto the line filter the same way as the old cord). What I need is assistance on the On/Off switch wiring
Quoted from iamdrunker:Let me know if you need me to check continuity or polarity. [quoted image]
I bought a 2-prong (or 2-wire) switch, and that's why it's not working. Thank you very much, I will most likely buy a replacement line filter as well since there's a high chance I blew it up
Quoted from iamdrunker:It's a single throw, Dbl pole switch. like you're schematic shows. If I'm reading that right.
I had it wired like this:
1 wire of the switch, both neutral wires (one for the service switch, one for the line filter), and the blue wire
1 wire of the switch, both hot wires (one for the service switch, one for the line filter), and the yellow wire
Here's the switch I'm currently using: https://www.amazon.com/gp/product/B01IYKSLCG/ref=ppx_yo_dt_b_asin_title_o00_s00
Quoted from Quench:That switch has 3 positions (ON-OFF-ON).
You want a switch with 2 positions (ON-ON) where you don't use the second ON position - one of these will do:
amazon.com link »
amazon.com link »
amazon.com link »
Thank you. Then how do I hook up the wires? Same as the factory one (in the picture posted by iamdrunker)?
Quoted from Quench:Please be very careful here, the way you wired that first switch would have blown the house fuse.
iamdrunker has his power switch wired to match factory, but it only shows part of the story. If other wiring on your game has been incorrectly wired (i.e. your power cable/plug or the connections to the EMI filter) you could have issues.
Put some heatshrink tubing over the power switch connections so you don't accidentally touch the connections and get zapped.
Essentially the wire from the active (hot) pin on the power plug must reach the final destination of J2 pin 6 on the rectifier board.
J2 pin 7 is the neutral (return) wire to your power plugs neutral pin.
If you're not aware, the wire colors are coded on the schematics:
[quoted image]
Here's how my EMI filter's wired. The Blue wire coming off the fliter is crimped to the black wire that leads to the switch, and the Brown wire coming off the filter is crimped to the white wire that leads to the switch.
20201029_142831 (resized).jpg20201029_142833 (2) (resized).jpgYou're currently viewing posts by Pinsider Knxwledge.
Click here to go back to viewing the entire thread.
Wanna join the discussion? Please sign in to reply to this topic.
Great to see you're enjoying Pinside! Did you know Pinside is able to run without any 3rd-party banners or ads, thanks to the support from our visitors? Please consider a donation to Pinside and get anext to your username to show for it! Or better yet, subscribe to Pinside+!
This page was printed from https://pinside.com/pinball/forum/topic/lost-world-wiring-a-power-switch?tu=Knxwledge and we tried optimising it for printing. Some page elements may have been deliberately hidden.
Scan the QR code on the left to jump to the URL this document was printed from.
Ramona, CA