Quoted from ThatOneDude:

Can someone share a pic of the little mechanism that drops the drop target for the snagger? I have most of the assembly, but I am missing the little bracket that holds it on to the larger mechanism. I am including a picture of the part of the mech that I have. The part I need is the bracket that holds this to the snagger. If you happen to have one handy that can be measured, that's even better. Or, if you have one you would sell, that works, too.
[quoted image]

Quoted from K-Reeb:

Sorry to be late to the game, but here is a pic of my start button as well as some pics of the drop target bracket being discussed. I can take more if needed from different angles.
I have been having issues with my drop target for the past few months; the target stopped dropping during ball lock. I think I just have to tighten a few screws and it should be fine. Worst-case, I may need to add a little length to the poker as it doesn't seem to be reaching the drop target.
[quoted image][quoted image][quoted image]

Quoted from K-Reeb:

After adjusting the bracket, it is properly making contact with the drop target when I press it down, but still no luck in regaining total functionality.
The coil is not firing in test mode. The brown and brown/violet wire connections were replaced with alligator clips prior to me buying it last year; they're a little looser than I'd like and maybe that's the issue. The coil was also replaced 2-3 years ago, but it could have gone bad since.
I'll start with the wires and order a new coil if that doesn't work.

Quoted from Deafman013:

Hi Stebel,
Great idea and have just ordered led strip for the rear to make it look even better.
Cheers
Brett

Quoted from Stebel:

Post before and after pics when you do the install.
I don’t actually own this game. I just fix it for a customer. He won’t sell it to me!! Hard to come by otherwise.
I just added a yellow strip to Congo and the results were splendid.

Quoted from Deafman013:

Does anyone know if possible to get new cabinet sticker for the cabinets?
Ours is pretty worn out around the flipper buttons and few scratches down the side where book shelve came off the wall and damaged it.

Quoted from Spazpeker:

Hi, my CPU card battery leaked and ruined the board, I bought a new Bally board and everything seemed to work ok,
However I tried to setup my snagger and under the diagnostics there is only one Lost icon to test the playfield magnet that works ok.
the snagger motor does not appear in the menu.page 30 of the manual.
also under adjustments page 38, item 49 says not used instead of Snagger enabled.
any ideas ?

Quoted from Socashi:

New owner of a RE import lost world machine. The cabs in rough shape but the playfield looking solid aside from a few wear spots. Hoping to sand down repaint and find some decent graphics for the sides. I was wondering if anyone knows much about the magnet hold in the back playfield and if replacements can be found and if its supposed to be flush with the playfield or stick up. I have a picture of mine which looks pretty worn down.
[quoted image]

Quoted from Socashi:

Took a look and im guessing its these threaded core plugs?

Thank you for the image and advice on how to remove it, The jam nut is on there super tight. hoping I get get it loosened later tonight and take that bolt off.

Quoted from SimplePin:

My timing belt in the snagger broke today. The black thin one in the front of snagger. Not the wide one that goes under the playfield. Wondering if anyone has replaced this before and has any pics, tips or other advice on the simplest way to replace the belt. The part is only 8 bucks at Marco so that's good.
Wondering if I should replace them both while I'm at it. But I'm a strong believer in if it ain't broke don't fix it!
Thanks!

Quoted from SimplePin:

Finally got around to replacing the black timing belt. Re-assembled the mech. Now what? Nothing happens and I can't get either of the two snagger tests to run. Is there a trick? Is there something I missed? I didn't touch anything under the playfield but everything looks ok after poking around.

Quoted from SimplePin:

Finally got around to replacing the black timing belt. Re-assembled the mech. Now what? Nothing happens and I can't get either of the two snagger tests to run. Is there a trick? Is there something I missed? I didn't touch anything under the playfield but everything looks ok after poking around.

Quoted from SimplePin:

Extended as that was where it ended up when the belt broke. Should I rebuild in the home position?

Quoted from SimplePin:

I have replaced my belt and the snagger is now going up and down however when the it tries to drop the ball into the truck the bottom section of snagger isn't close enough to the front of the truck for the ball to fall through the roof of the truck. I'm not seeing this "click" method in the manual. Which belt are you clicking one tooth to adjust. the red or the black?
Thanks!

Quoted from rwarren28806:

See post 424....

Quoted from dung:

Got one today. Is there supposed to be a delay after you hit start? Dmd changes to show ball 1 and then the game sits for 3-5 seconds before kick a ball into the shooter lane and running the intro animation.

Quoted from CaptainStabbin:Also, does anybody know if any insert decals exist? The big circular insert on mine that is in front of baby t-Rex egg that has part of the baby t-Rex foot art work on it had completely flaked off of the playfield. I have it held back down with tape for now but it’s destroyed. Not sure what caused that, because my playfield is actually pretty nice. Possibly some kind of adhesion issue on that insert/heat from the old bulbs? Does anyone know if any decals exist for this or have any recommendations? I’m good with the mechanical and electrical side of things, but artwork is my weak side.
[quoted image]