Junk Yard Club all Welcome

I should be a member in the next month or so. The seller is currently doing a full shop job. I just read through this whole thread lol
I'll be getting some art blades right away and a colordmd when I can afford it. I'd like to paint the van to look a little dingier but I'm a crappy artist. Mostly just posting here now so this thread shows up in my watchlist.

Are the 3D printed car stacks still available?
They look really sharp.
I'll be putting in some side blades. I've found these 2 but does anyone know of any other options out there?

20190226_201223 (resized).jpg20190226_201244 (resized).jpg

Supposed to arrive at a depot near me on Monday. I will post pics Tuesday or Wednesday when I pick it up. So nervous and excited in the meantime.

image000000 (resized).jpg

image0000002 (resized).jpg

image000003 (resized).jpg

Maybe by western standards :p
Should I take it that's you?

It arrived in Woodstock today. Renting a van to go get it tomorrow.
Waiting on a couple small pieces and some side blades. I'd like to put a color dmd in when I can afford it.

Any advice please
I just got my junkyard this week. I havent had much time with her but I have 6-10 lights that either light up fully at times they shouldnt or some that are ghosting. The LEDs in it are comet and the seller says it was not doing this before shipping. I checked to make sure my connections are secure. Are ideas before I dig into it next week?
Oh, also, if someone could maybe post a pic of the auto plunge hinge area it would be helpful. Mine took some damage in transit and I'm pretty sure a small piece is missing from the left part of the hinge. It still fires bit it is loose and jiggles and rest on the plunger tip most of the time. Lighting is my first issue as I'm not good with circuitry. I can fix flippers and mechanical things but I'm just not very skilled or knowledgeable with the boards etc

I've got my junkyard at about 98%
I could use some advise for the folloiing issue.
When the ball is plunged it awards/starts whatever is ready at the sewer (or some toast). It does this about 80% of the time. The opto seems to be lined up well and works 100% of the time outside of the plunge issue. It makes the game so much easier though lol

No. I get spinner as normal but also recieved sewer.

It also cycles through all the balls twice on boot up then plays ok.

Not working
31 trough opto
41 opto after spinner
51 left sling leaves

Cant see anything obviously wrong

Still working out those bugs
I have a dumb question.
Where does this go? It doesnt seem to match any existing chips. I figured it would be a 2 minute swap but I'm just staring at the boards looking for a match. Thanks.

20190503_135958 (resized).jpg20190503_140029 (resized).jpg

Thanks. Could you send me a pic or circle it in the pic I posted? I've only had it for a month. I will probably put an nvram in eventually.

Yay! My Junkyard is 100% again. After much searching I finally found a popped solder joint. 2 minute fix and shes good as new. Installed replacement Bob and Spike decals, some titans rings and fixed a few lighting/switch issues. Looking good. Now I just need to update to ver 1.2

Just looking for some confirmation.
After moving the playfield my crane doesnt want to stay up anymore. I took a look and the coil have a popped solder joint and I found a loose frayed brown wire with a purple stripe. It's almost a given that the wire goes to the coil but I'd like some confirmation before I solder it back on incase I'm way off base. Anybody that can send me a pic of the back of your crane would be helping me out. Cheers.

20190510_003658 (resized).jpg

20190510_003710 (resized).jpg

Out of the club. Just didnt work in a smaller collection. Took a tiny hit on the sale but it frees up cash for something new. The new owners should be pleased though. I basically did nothing but fix the game up while I had it. She is a beauty.