Jokerz!
Williams, 1988You're currently viewing posts by Pinsider wizard15425.
Click here to go back to viewing the entire thread.
I just picked up a Jokerz! I accidentally revered the 12vdc feed to the poker wheel board. It has stopped working. I can’t seem to find the wheel schematic in manual. Does anyone know of a poker wheel schematic available to download?
TIA.
Quoted from WiZaRd15425:I just picked up a Jokerz! I accidentally revered the 12vdc feed to the poker wheel board. It has stopped working. I can’t seem to find the wheel schematic in manual. Does anyone know of a poker wheel schematic available to download?
TIA.
Quoted from meSz:It's my understanding that the Motor Control Board (D-12045) that was used in Jokerz was also used in Cyclone and Riverboat Gambler. Here's the schematic that I found for Cyclone so you should be able to use it!
[quoted image][quoted image]
Thank you for the schematic. I found some bad components (7805, LM339) replaced with new components, but I still get the err error in wheel test. Motor spins only counter clockwise and way too slow. Optic switch is working in switch test. Don’t really what to look at next. Any help would be appreciated. TIA
Quoted from Morinack:[quoted image][quoted image]
I accidentally reversed the 12vdc at the interconnect board connector 12 feed.
Also, The schematic doesn’t match the pin traces on my board for LM339. Schematic shows pins 5,6,
9, and 10 as connected. On board 6 is going to R6 and 5 has no trace. I’m confused with that for sure. Optic is working in switch test and during wheel test but wheel is very slow and display shows err error, Home switch which is opto 1 think, is working. Don’t know what err is relating to. Trying to figure out what voltage should be present at motor pins 1&2 and 5&6
Motor is a 9 Vdc motor and I’m getting only 7 volt to motor at pins 1&2 and 5&6. Not sure where problem could be.
Quoted from Morinack:I believe the err is a homing issue. My test shows it briefly at the beginning of the test.
I'll take another look at what I have.
Here is a video of what I’m getting in wheel test
https://www.facebook.com/groups/609432482409545/permalink/4786371368048948/
Quoted from Morinack:i was able to somewhat simulate your symptom by un plugging J17 on interconnect.
pins J17-1 and J17-8 are P1-1 and P1-3 on the motor schematic.
Motor still spun at speed but gave me 256 err.
Make sure it is seated correctly on interconnect board.
Ok I’ll check that. Do you think this motor will work with Jokerz.
https://www.robotshop.com/en/rbsoy02-soyo-unipolar-stepper-motor.html
I think my motor is bad. I’m getting correct pulses from cpu transistors but only slow speed works.
Marco wants $69 ft it the motor. The above motor is $16
You're currently viewing posts by Pinsider wizard15425.
Click here to go back to viewing the entire thread.
Wanna join the discussion? Please sign in to reply to this topic.
Great to see you're enjoying Pinside! Did you know Pinside is able to run without any 3rd-party banners or ads, thanks to the support from our visitors? Please consider a donation to Pinside and get anext to your username to show for it! Or better yet, subscribe to Pinside+!
This page was printed from https://pinside.com/pinball/forum/topic/jokerz-club-quite-now-we-are-playing?tu=wizard15425 and we tried optimising it for printing. Some page elements may have been deliberately hidden.
Scan the QR code on the left to jump to the URL this document was printed from.
Connellsville, PA