Ditto

Bumping this thread to see about alternative panels in the JJP machines (which fit)? I did some self-induced damage to one of mine, and ordered the same stock part number from China (it's the same panel that comes in an all-in-one Lenova PC, no US resellers have it, and JJP wants $600 but it probably includes the entire assembly). Would love to know if any replacements fit (and look better!).

Got my M270HVN02.0 from China. Simple swap other than the light strip at the bottom. Cable goes from a 2 pin plug, soldered to the light strip +/- on the original display, to a 6 pin configuration I’ve never seen on the new display. Comes out of this port (circled) on the control board. Any ideas?

A881B1F5-EEE4-4502-9088-2A440AF6D731 (resized).jpeg

D8354DFE-6A38-46AC-B92B-08279A15A1A8 (resized).jpeg

E042D071-8B94-490F-88C9-5CCA889A2485 (resized).jpeg

I'll try to explain, but everything is back together now, so can't take any new pictures. For the record, I'm in this for hobby now, because it wasn't a simple swap, I just ordered the replacement assembly from JJP, but as I'm and intrigued tinkerer (and have a monitor from China that I don't want to send back!), I'm going to try to see this through...

I bought the M270HVN02.0 from China (I have a missing pixel on one of my JJP games that was likely self-induced during installation). That was the serial number on the back of the bracket holding the LCD screen. It appears to be the exact same panel, the only difference being the way that the LCD backlight is powered (the LVDS cable is the same). The one that came with it, has a red/black pair (that you can see in my picture) that is soldered to the power of the backlight strip (it runs into a hole in the corner of the back metal panel of the display), and it plugs into the control card. The new one, has a tiny 6-pin connector, which is presumably the backlight control (LVDS is the same). So it appears the spec on the monitor has changed. So what to do... On ebay, I found a controller board which is compatible with the new display (and the 2.1, 2.3, and about 200 other displays).
ebay.com link: HDMI DVI VGA LVDS LCD Controller Board For M270HVN02 0 1920x1080 LED Screen

This ensemble doesn't have the simple two wire power to go to the LED backlight (like the one that came on the pin), but it does have a connector to an inverter board (I don't know enough about the electronics to understand why an inverter board is needed, assuming to condition the power), which then has a wire that will go out and plug into that small 6-pin connector on the back of the new display. I don't know if any of this will fit on the mounting posts on the JJP bracket (stuck to the backside of the display), but I think I can either 3d print or buy some plastic posts with stick on the button (presuming this solution/display is any better than the stock one from JJP).

That's what I know so far! happyclan is on a similar path, and he'll probably get his China order before me.

I’m waiting for the compatible control PCB from Hong Kong. Should be soon I hope.

I’ve got an update as well. The board I ordered has all the right connections (inverter and cable), but..... the monitor I have, is the same size visible screen, however the bezel is materially smaller. Ugh. So no direct replacement into the JJP mounting hardware. I’m thinking about printing some some blocks that I can wedge in and maybe use some gorilla double side tape to hold it in. Custom brackets would be nice or some really long (and thin) screws not sure if they exist. It’s about 5-10mm per side/top/bottom.

In the mean time I got the replacement from JJP and it came assembled and took 5 mins to swap in. And it seems much richer in color (less washed out) than the old one.

F614ED7E-CF6A-43CB-8305-412A914BC598 (resized).jpeg

So I’m at the same place you are, but the problem I had is that the bezel on the new monitor is so much smaller, it doesn’t mount properly in JJP’s mount. Have you tried this yet? I think I could make a part (bracket or print) to make it fit.

As for mounting the controller board, I agree with your PM, to just route the hdmi cable in there and mount the board with a 3D print, or post sleeves with double sided tape. Won’t be pretty but who cares.

1PC new M270HVN02.0 All-in-one PC screen 27 inch LCD screen

Bezel might not be the right word. The silver metal surrounding the screen and I do not believe they are removable. I posted a picture a few back I believe showing the issue.

I haven’t worked on it.

I have it all ready to, but bought a replacement monitor from JJP so now my experimenting is just for fun (or until I need another). I can pretty easily figure out if it will auto power on though if that would be helpful, see if my control board is different.

I don’t think the original JJP board will be compatible with the new monitor which has that 6-pin plug.

This is an old thread, so my memory is a little outdated on it, but I ordered boards and monitors (from China) and I believe I rebuilt a solution, but also ended up just getting a new one from JJP because it was way more challenging than it should have been to try to rebuild on my own.