Quoted from Guinnesstime:
Happy for now. Need the 3D cyborg next.
Where did you get the piece of mind eddie? Who makes it? Thx
Is there anyone who knows where to buy a splitter for this plug so I can add another rgb led ? This is the one under the clairvoyant orb on the premium. Or is there anyone that can make a splitter with another rgb led set up?
I want to add another led on top with an orb but leave the original under the plastic.
Thx I got them and made the splitter up just waiting on my rgb led and crystal ball
On a side note does anyone know where to find the clairvoyant plastic without buying the whole set from stern
Where did you get the plastic protectors ? And is there one for the skill shot plastic I’m already getting hits and wear
Yeah those are cool but seem way too bright and white. Maybe a yellow or red led would look good. I like the idea though
Does anyone know of a full set of plastic protectors for the premium/ LE? I really like the yellow stuff I’ve seen but no one has the protectors for the plastic over the stand up skill shot plastic.
Are the original target decals available, I think lit up with the proper colors and the decals they would look great
I even think if the decals aren’t translucent the rest of the target will still light up nicely
I’m ordering a set to try it
Ok so I got my drop targets but didn’t look under the playfield first. It is a board as opposed to individual leds. Does anyone know how to tie into the game to get the correct leds on the correct targets. I know I can have then colored correctly and lit all the time but I’d prefer on and off with the game if possible.
Any help is appreciated. I am not a wiring schematic guy so I can’t look at the manual and remotely figure it out.
Yes I’d like to add correct leds to light the corresponding targets but have no idea how to go about adding the leds. I don’t want to blow up the game trying to figure it out. I’m sure it’s a matter of adding a type of male/ female adaptor and wiring the correct color leds but I’m at a loss as to how.
Quoted from vireland:
Just a preview of something else I'm working on for Iron Maiden. I want to start by getting that diorama on the left into 3D. Anubis was the hard part, so now I just have to do the columns on the left and right of him and figure out coloring/lighting. It's an encouraging start, though.
Looks good, will it work on the premium?
Quoted from Skeets:
I'm not much of a mod guy, but the aftermarket orb dome thingie was a little too large for my taste. On the pro, its really hard to see the orb dome lit up when it is flashing from underneath, since there is no newton ball for it to reflect the light. Solution for me, steal the blue dome from the right side of the playfield, bore out the appropriate size hole on the plastic, and flip the dome to the top, just like the dome to the left in the pic. You can do this yourself if you are brave enough to modify the plastic. Just make sure you protect the LED board from underneath since it will be exposed. Meaning you don't want the ball to be able to hit the LED board. I used another clear plastic underneath, but you can use just about anything.[quoted image]
I made this and flipped the led under the plastic and never drilled out the plastic and it works perfectly and I like the look but it’s not too overpowering in the game
I could make some more if people are interested.
I used the existing led and just flipped it so it faces up underneath the plastic and added a washer to keep it level and used the next size up in length screw
Works like a charm
I have a few people interested so I’ll order more stuff to make a few
Quoted from Fytr:
Very cool. Couldn't have been easy working with such a small area. Care to share how you did it?
I drilled from front to back aiming towards his neck area with a tiny bit then kept going up one size until a Pico led fit in from the back. The less are about halfway in as they are too bright at the actual eye ball
Wasn’t as bad as you might think
Quoted from bigduke6:
Awesome job. This could be my favorite upgrade. Where did you pick up the leds?
Thx. I used Evans designs, they are a model train led website but have a ton of great leds. I used Pico warm led 6-12v iirc. I bought cool also to try but they were too white.
Working on my spitfire mod now. Hopefully it will be finished over the weekend. Then I need to find a replacement somewhere in time eddie and give him a little upgrade.
So I finished my spitfire mod and on heating the shrink tubing over the wires I melted my prop. going to order another now ...... so close. Didn’t even get to see it mounted and spinning In the game!
Quoted from jrivelli:
Posted in the other IMDN thread but finished the pop bumper truecolor protectors
Of course one of my pop bumper light boards is out atm so only 2 are lit up in the pic
Looks good I’m in but the link doesn’t seem to work.
So I’m gauging interest in my orb mod. I’m starting a thread but am posting here as well.
I will have two sizes, 3/4” and 1”. Both look good to me so you can have your pick.
I’m including the necessary longer screw and spacers as well.
More details on the thread I’m starting but I’m thinking $30 shipped.
It may indeed work on a pro but I do not have one to test/use. I do just use the existing LED that is under the plastic which normally faces down and I flip it to face up if you look at my iron maiden orb mod thread I have a little more detail and pictures
I made a plane mod with the prop that spins but the motor got too hot and overheated and started to melt the plastic so I disconnected it. I did the same and painted extra yellow on the prop and it looked great, but ultimately no one got to see it but me.
Still looks good though.(the pic is when the prop still spun)
Quoted from Mikonos:
Some Iron Maiden Pinball users asked me for a custom rules card, you can check it here:
For my own entertainment I designed another pinball card, this is a "Free Play" card:
Opinions and improvement suggestions are welcome!
Those look great! Any plans on a premium themed set?
Quoted from Wotto:
A mate was telling me of 'someone' overseas( I know I know, not much info to work with ) who makes custom side armour for games - including IMDN.
Anyone know who that might be? ( not the generic Stern Mummy Fist side armour that you can buy at a few places )
Appreciate any direction on this - thanks
Is this what you are looking for
I love when the game goes red in fear of the dark!
Great to see you're enjoying Pinside! Did you know Pinside is able to run thanks to donations from our visitors? Please donate to Pinside, support the site and get anext to your username to show for it! Donate to Pinside