(Topic ID: 68869)

IJ Williams "You Cheat, Dr. Jones!" Club


By RDReynolds

5 years ago



Topic Stats

  • 4,835 posts
  • 398 Pinsiders participating
  • Latest reply 21 hours ago by Energyspike
  • Topic is favorited by 193 Pinsiders

You

Linked Games

Topic Gallery

There have been 1,599 images uploaded to this topic. (View topic image gallery).

917ECE83-3109-4225-AEE9-84C480CB0C08 (resized).jpeg
46914232-1815-40BB-9333-951DCCC48D73 (resized).jpeg
90CEF4CF-B0BE-4D53-81DE-CC077AE98A52 (resized).jpeg
A267B015-A397-473C-972F-F5BC78F15A05 (resized).jpeg
DSCN4928 (resized).JPG
DSCN4924 (resized).JPG
F31487F9-02AD-4737-B2A3-AB998BA7D075 (resized).jpeg
53A4A204-328D-46E2-B5D5-AA7C42AAC962 (resized).jpeg
CCCAA565-3D31-4435-A8E5-995C2FDEF470 (resized).jpeg
E84F67CD-4DB5-49C8-9E0B-2070B4E339A1 (resized).jpeg
40CB038B-2C28-40D1-B42B-33F8E983F435 (resized).jpeg
821AD53A-1D2B-4FB1-8EC6-3BD538802C40 (resized).jpeg
3AEC8BA3-3787-4F03-A4EE-5A774FC4E4C1 (resized).jpeg
9930169A-8F2B-4C8F-9BEF-79EF26A4A991 (resized).jpeg
DSCN4778 (resized).JPG
DSCN4780 (resized).JPG

You're currently viewing posts by Pinsider gliebig.
Click here to go back to viewing the entire thread.

#4560 86 days ago
Quoted from Djshakes:

FYI regarding airball mod. I was told that if you have the lost plastic it pushes pieces around the single drop target forward making installation difficult. If you have a lost plastic on your back board please specify and I will modify the single drop piece to accommodate.
$25 both pieces. mr_brandt@hotmail.com
[quoted image]
[quoted image]

Where do these drop target mods come from?

1 week later
#4625 74 days ago

Joined yesterday.

Didn't get it setup until late, so I haven't properly leveled it.
Question:
1 After the post drops for the ball to go into the POA, it wasn't dropping in but going past the POA and into the left lane. Is that a level and or pitch adjustment issue?
2 Are the Lites Hand of Fate inserts on the inlanes always lit?
indy (resized).jpeg

#4627 74 days ago

Thanks. My phone says I'm a 7.5. It doesn't play like it's that steep.

Another quicky....what is the skill shot?

(i only got to play a couple games last night)

#4642 70 days ago

I recently brought home a IJ.
It played fine for a while. Occasionally it would throw a switch error that would go away on it's own. Last night I'm playing and do a small slap save...left flipper dies a few times and game resets. Then the sound goes out. Sound comes back on then the DMD goes out and stays out. A couple balls are locked in the idol which aren't freed by ball search. It then just starts shooting out balls repeatedly and flippers don't work. It became possessed.

Any ideas? When I brought it home, the lights and dmd were out, but I found that a plug had just come out during transport. Easy fix. I'm not sure what is causing all these issues.

#4646 69 days ago
Quoted from Ricochet:

Your ribbon cables could have intermittent issues (try re-seating all of them) ... this is a common problem with the age of these things.
You're 5V could be getting flaky (this can cause erroneous resets during game play)

Reseated every ribbon cable and plug.
Dumb question...how do I check the 5v on this game?

#4647 69 days ago

Do these go anywhere? Didn't see a spot for them.

20190810_103956 (resized).jpg20190810_104049 (resized).jpg
#4648 69 days ago

I put black on ground and red on lower right prong of the chip but didn't get a reading. Must be doing it wrong.

20190810_101101 (resized).jpg
#4650 69 days ago

That was what I figured. Just wanted to double check

#4667 64 days ago

My POA post isn't dropping when the ball is up there. What should i look for?

#4671 64 days ago
Quoted from Ricochet:

1. Check for mechanical linkage... my solenoid assembly had loosened over time and the post wasn't working the way it should.
2. Check coil, go into test mode and see if the coil is activating.
3. Dig in and check from the coil back to the driver board (diode, connections, transistor).

Moves freely but doesn't work in test. Must be stuck. Smells like it's burning and is hot

Promoted items from the Pinside Marketplace
8,999 (OBO)
Machine - For Sale
Hingham, MA
$ 49.95
Playfield - Toys/Add-ons
pinballmod

You're currently viewing posts by Pinsider gliebig.
Click here to go back to viewing the entire thread.

Hey there! Got a moment?

Great to see you're enjoying Pinside! Did you know Pinside is able to run thanks to donations from our visitors? Please donate to Pinside, support the site and get anext to your username to show for it! Donate to Pinside