(Topic ID: 199375)

How To Disconnect 1980 Stern Coin Door Wire Connector


By clodpole

2 years ago



Topic Stats

  • 13 posts
  • 4 Pinsiders participating
  • Latest reply 2 years ago by clodpole
  • No one calls this topic a favorite

You

Linked Games

Topic Gallery

There have been 3 images uploaded to this topic. (View topic image gallery).

IMG_0091 (resized).JPG
wiggle (resized).jpg
IMG_1416a (resized).jpg

You're currently viewing posts by Pinsider clodpole.
Click here to go back to viewing the entire thread.

#1 2 years ago

Wires from coin door insert into half of a white plastic connector which joins a mated opposite. The halves are held together by springy fingers with little flat-ended ramps to keep the connectors from separating. I can't figure out how to get the springy ramps depressed so that I can take the two sides of the connector apart. Any suggestions?

I'm trying to get my "QUARTER" lights to light on the coin door but they are getting no voltage. I suspect a bad connection inside the first connector box.

Thanks!

#4 2 years ago

>Called a 'friction lock' -- just grab and pull.

It isn't only friction; you can just make out 2 small tabs with spring locks on them in the photo above. Pulling alone doesn't release the tabs and so far I haven't figured out how....

#8 2 years ago

Thanks for the instructions (and the excellent "how-to" photograph) - I'll give it a try this afternoon.

Meanwhile, do you have a coin box you could photograph or measure? I'm trying to find one of those, but only know the measurements of the inside of my cabinet.

Best wishes!

#9 2 years ago

OK, I put a drop of alcohol between the halves of the plastic connector box and then wiggled (Tom Jones music goes here). It came apart, happily - thanks again for the encouragement. Unfortunately, no progress was made on the unlit "Quarter" slots; connectivity tester showed no breaks from connector box to coin slots. I'll have to chase it farther upstream.

I note my machine has 2 quarter slots and most photos I see show flight 2000s having 3. Maybe I got a replacement door with my used machine....

#11 2 years ago

I'll try tracing back to that board and see what I find. Thanks anyway as regards coin box measurements.

#12 2 years ago

"...my coin door has 3 slots , 2 quarter & 1 dollar coin slot
I don't have a coin box for your measurements
my coin door lamp wires seem to trace back to the Rectifier board ( I just happened to have my playfield up working on feature lamp sockets)"

Ahhh... no power on the rectifier board pins to the coin door lights. Having a real solid state repairman over to do the remainder of the fix for me; my soldering skills are better suited to the industrial size connections on an EM.

#13 2 years ago

Final resolution: coin door lights were off 'cause one wire was in the wrong connector on the J2 section of the rectifier board - slot 4 instead of slot 5. Once that was moved, the lights came on.

IMG_0091 (resized).JPG

Promoted items from the Pinside Marketplace
1,400 (OBO)
Machine - For Sale
Carlisle, MA
850
Machine - For Sale
Ashland, OH
From: $ 15.00
From: $ 10.00
From: $ 18.00
Apparel - Men
Pinside Shop
$ 5.00
Playfield - Decals
Doc's Pinball Shop
$ 119.95
Boards
Allteksystems

You're currently viewing posts by Pinsider clodpole.
Click here to go back to viewing the entire thread.

Hey there! Got a moment?

Great to see you're enjoying Pinside! Did you know Pinside is able to run thanks to donations from our visitors? Please donate to Pinside, support the site and get anext to your username to show for it! Donate to Pinside