(Topic ID: 239267)

Gottlieb King Rock startup problems

By n1teowl

1 year ago

Topic Stats

  • 6 posts
  • 2 Pinsiders participating
  • Latest reply 1 year ago by n1teowl
  • No one calls this topic a favorite


Linked Games

Topic Gallery

There have been 2 images uploaded to this topic. (View topic image gallery).

Pinball (resized).png
Pinball (resized).png

You're currently viewing posts by Pinsider n1teowl.
Click here to go back to viewing the entire thread.

#1 1 year ago

Hi all. I have a new King Rock project, and I was hoping I could get further before posting here. I'm hoping someone can provide me some direction. When I turn the machine on, there are no lights anywhere, except for a lone coin slot light. When I press start, I get a one third turn of the score motor and it stops. Every time I press the button, I get another one third turn. The start relay fires, along with the replay button relay. The hold relay also fires and locks. That's about it. The start relay does not lock like it should. I have investigated the many tilt switches and bounce switches and I believe I have them all in the right state. I do have a question about the tilt switches, though. On the schematic, they are all three in a parallel and are all normally open. When I test the continuity on both sides of these switches, it buzzes. Does that mean at least one of them is closed? Anyway, I'm unsure if a tilt switch would be to blame for these other issues. If I close the tilt relay, some of the lights on the playfield come on so there is power there. I can't get anything in the backbox to do anything, no lights, no relays. The only exception is that if I add a credit to the credit wheel manually, the knocker fires (in the cabinet). It's all very confusing. Any thoughts on where to look next? Many thanks in advance.

#3 1 year ago

Thanks for posting that. I don't get too far unfortunately. I get past #1 and then the lock on part in #2 doesn't happen. Step 3 does happen, but it never gets to 4, presumably because there's no closed switch on the "S" relay.

#5 1 year ago

Thanks again for the clip. I'm sure this will help a lot. I have looked into the anti-cheat switch and score motor, but this will help me focus better. I'll let you know what I find out.

#6 1 year ago

I worked on it a bit today and no luck yet. I think something is just slightly off because a few times the score motor kept turning past a third of a turn, maybe making up to two revolutions. I figure that if I can get it constantly spinning then I'm on to the next problem.

Promoted items from the Pinside Marketplace
From: $ 18.00
Apparel - Men
Pinside Shop
$ 4.49
Yorktown Arcade Supply
$ 12.00
Lighting - Led
Pinball Haus
$ 249.99
Cabinet - Armor And Blades
Id Rather Play Pinball
$ 44.00
Playfield - Toys/Add-ons
$ 128.00
Playfield - Other
ModFather Pinball Mods
€ 222.00
Cabinet - Decals
$ 154.00
Cabinet - Toppers
Id Rather Play Pinball
$ 7,899.00
Pinball Machine
Operation Pinball
$ 200.00
Lighting - Interactive
Professor Pinball
From: $ 175.00
Gameroom - Decorations
Pinball Photos
$ 28.00
Playfield - Toys/Add-ons
$ 19.95
Playfield - Toys/Add-ons
$ 35.00
Cabinet - Decals
Pinball Haus
From: $ 39.00
Cabinet - Toppers
Full Tilt Pinball LEDs
$ 150.00
Cabinet - Toppers
Rock Custom Pinball
$ 7,599.00
Pinball Machine
Little Shop Of Games
$ 54.99
Cabinet - Shooter Rods
Lighted Pinball Mods
$ 18,500.00
Pinball Machine
$ 119.95
Cabinet - Shooter Rods
Super Skill Shot Shop
$ 24.25
Playfield - Toys/Add-ons
The MOD Couple
$ 9.99
$ 139.00
Playfield - Toys/Add-ons
Sparky Pinball

You're currently viewing posts by Pinsider n1teowl.
Click here to go back to viewing the entire thread.

Hey there! Got a moment?

Great to see you're enjoying Pinside! Did you know Pinside is able to run thanks to donations from our visitors? Please donate to Pinside, support the site and get anext to your username to show for it! Donate to Pinside