(Topic ID: 216794)

Drop target bank PF alignment?

By hisokajp

5 years ago



Topic Stats

  • 8 posts
  • 5 Pinsiders participating
  • Latest reply 5 years ago by hisokajp
  • Topic is favorited by 1 Pinsider

You

Linked Games

Topic Gallery

View topic image gallery

image (resized).jpg
image (resized).jpg
62FE7747-0896-44B1-A438-140BCC74004B (resized).jpeg
20180512_130453 (resized).jpg
20180512_130422 (resized).jpg
20180512_130435 (resized).jpg
20180512_130426 (resized).jpg

You're currently viewing posts by Pinsider hisokajp.
Click here to go back to viewing the entire thread.

#1 5 years ago

So i decided to treat my hotdoggin with a full new set of drop targets from PBR (4+3+3) and after a couple hours to take appart all 3 assemblies and put them back on i can get the top of the target flush with the PF...

I do not find a way to adjust the height of the target, i feel like the position of the hole at the bottom of the drop target is slightly higher than on the old ones i replaced. the metal arm lower position is fixed by the bottom of the assembly (near the SW) but that cannot be adjusted.
Is the issue with the PBR drop target? Any way to adjust this without hacksaw the slot deeper for the arm to drop lower?
am i missing something?

20180512_130426 (resized).jpg20180512_130426 (resized).jpg

20180512_130435 (resized).jpg20180512_130435 (resized).jpg

20180512_130422 (resized).jpg20180512_130422 (resized).jpg

20180512_130453 (resized).jpg20180512_130453 (resized).jpg

#5 5 years ago

yeah it does not look like the plate is adjustable, it screws on the main assembly, no real adjustment.

Lowering assembly maybe a good idea, some of these post rubbers maybe? Like the CFTBL window... it's either that or filling the divot where the crank goes down to make it lower...
those drop target side to side with the old one do look pretty different, i am going to have to check with PBR what are their thoughts on this...

#8 5 years ago
Quoted from Madmax541:

Try flipping 180 cover plate in picture opposite DT

Ding ding ding! Madmax was right! somewhow whoever have worked on the assembly before me had them all reversed, all good now!

Also once reversed, the inline drop target can indeed be adjusted to make sure they are perfectly aligned. one common plate for all 3 targets but still worked, thanks all!

Promoted items from the Pinside Marketplace
$ 119.95
Boards
Allteksystems
Boards
$ 18.95
Eproms
Pinballrom
Eproms
$ 44.99
Cabinet - Shooter Rods
Pinball Shark
Shooter rods
$ 9.00
Cabinet Parts
Third Coast Pinball
Cabinet parts
$ 5.95
Playfield - Protection
The Pinball Scientist
Protection
$ 9.95
Eproms
Pinballrom
Eproms
$ 10.00
$ 15.00
Hardware
Volcano Pinball
Hardware
From: $ 2.99
$ 25.00
Playfield - Plastics
UpKick Pinball
Plastics
$ 25.00
Cabinet Parts
Volcano Pinball
Cabinet parts
$ 8.00
Electronics
Third Coast Pinball
Electronics

You're currently viewing posts by Pinsider hisokajp.
Click here to go back to viewing the entire thread.

Reply

Wanna join the discussion? Please sign in to reply to this topic.

Hey there! Welcome to Pinside!

Donate to Pinside

Great to see you're enjoying Pinside! Did you know Pinside is able to run without any 3rd-party banners or ads, thanks to the support from our visitors? Please consider a donation to Pinside and get anext to your username to show for it! Or better yet, subscribe to Pinside+!


This page was printed from https://pinside.com/pinball/forum/topic/drop-target-bank-pf-alignment?tu=hisokajp and we tried optimising it for printing. Some page elements may have been deliberately hidden.

Scan the QR code on the left to jump to the URL this document was printed from.