Waiting for mine as well. Put in another good round of games at the Coin-Op free play day this weekend. Can't wait to get it in my house.
You're currently viewing posts by Pinsider vidiotgt.
Click here to go back to viewing the entire thread.
Waiting for mine as well. Put in another good round of games at the Coin-Op free play day this weekend. Can't wait to get it in my house.
I've been fighting with an impossible to hit Station 3 shot (statistics show no one hit it in 300 games!). I'm pretty terrible, but not that bad. After watching a bunch of videos I think my upper flipper might not adjusted just right. Can anyone confirm if this is correct or if it needs to be adjusted to swing out a bit more? If so about how far should it extend?
Quoted from Eskaybee:What's your pitch?
A touch past the second line on the bubble. My phone app wasn't very consistent, but at most a touch over 6.5.
Quoted from Zampinator:It looks like it needs to be adjusted out further. What does it look like in the resting position? Also, check that ramp(station 3). Mine had a wire hanging down by that ramp & the ball would hit it & slow the ball down enough to keep you from making the shot.
I read about the wire a while ago. I don't see anything like that. Just the hanging metal piece (switch?). When the flipper is at rest it sits right against the metal.
Quoted from bigd1979:Imo they used to small of a rubber on them (2in)i believe ....i changed mine out with 2.5 and they are much better.
I think the manual even calls for 2.5 now. I suspect they changed that out when they did the rev with the scoop protectors, leg protectors, and (I thought I read someone) the stiffer QED.
Quoted from spida1a:I hope this helps!
That did it! Shifted the play of the entire game.
Quoted from JWE:Does anyone else hear a buzzing sound not vibrating from the shaker each time the phone rings before multiball? Not sure if this is a bug or bad shaker motor. Thanks.
Yep, I think that is normal.
I also have a hiss from the speakers if you get close to them. Not sure if that is normal. They also pop twice when booting the system up.
The USB extension doesn't seem to work on mine (I don't even see the key in settings backup mode, need to debug that later). So I went to open the back box. They key turns a quarter turn cleanly with a little clank and I was able to loosen up the glass enough to lift it almost all the way but it seems to stop about 1-2mm too short to get over the frame at the bottom. Has anyone had that issue? I'm afraid to push it too hard (being glass and all).
Quoted from Damien:Anyone?
The old default gave you an extra ball for passing 250 or 300K score. They turned that off by default now.
Quoted from OnTheSnap:Mine is the same. I have to wiggle the machine to get it to nest. I'm at 6.5 degrees. I haven't really tried to fix it. Every good skill shot I'm pretty much wiggling the machine.
I had the cliffy in there and had to pull it out because it would make that happen on every single shot. After removing it I still got the issue from time to time. I played with bending the wire a bit and was able to resolve it. Since then I have only seen it happen once or so on a super floaty ball. I don't recall exactly how I bent it I just played with a bit with the glass off doing skill shots.
Quoted from Nokoro:How do you get the alternate Station 3?
That is the design that was used in the prototype design. Maybe convince someone with a prototype to trade?
You're currently viewing posts by Pinsider vidiotgt.
Click here to go back to viewing the entire thread.
Wanna join the discussion? Please sign in to reply to this topic.
Great to see you're enjoying Pinside! Did you know Pinside is able to run without any 3rd-party banners or ads, thanks to the support from our visitors? Please consider a donation to Pinside and get anext to your username to show for it! Or better yet, subscribe to Pinside+!
This page was printed from https://pinside.com/pinball/forum/topic/dialed-in-owners-and-fans-club?tu=vidiotgt and we tried optimising it for printing. Some page elements may have been deliberately hidden.
Scan the QR code on the left to jump to the URL this document was printed from.