Good lord almighty. Only had a day but I can't even score 1M!
You're currently viewing posts by Pinsider cserold.
Click here to go back to viewing the entire thread.
Quoted from tryton1000:Yeah....No. any other suggestions.
May have to add washers under the metal wireform in the locations where it is attached to playfield. May then need to do the same
For that top wireform if the ball doesn't clear the top wireform when traveling on the Lower one.
Quoted from tryton1000:It's not stuck on the wireform, there is a cutout in the pf protector where the flipper is, the ball is stuck on the lip of it.
I gotcha. Never put a playfield protector on before.
Why in the heck can't I find the setting to adjust the theatre magnet to prevent dropping the ball straight down the middle. I've read a negative setting is good but can anybody comment on where the hell this setting is and what number seems to work best. I'm at about a 6.6% pitch.
Quoted from PinMonk:It's in the tests under theatre test, not the game settings (for some strange reason). Start at -90 and go down (bigger negative number) from there.
Quoted from Pinballomatic:tests - device tests - theater test
-90 to -100
Thanks guys!
Quoted from Kevlar:Are there any spare/accessory power connectors on DI?
from what I understand JJP doesn't provide the 3 connector 12V extension like Stern does inside the cab. Per the recommendation of others, I ended up adding a separate 12V/3A power supply (http://a.co/6qfused) to the game that plugs directly into the service outlet on the power box in lower front right of cab. The challenge with this is that you have to make a couple simple wire modifications inside the power box to ensure that your external power supply turns off when you turn the game off...otherwise you have to fully unplug game from wall to get your mods that are plugged into the power supply to turn off.
Quoted from LTG:First thing is check if the optos are still stuck in the wall they are snapped into, on either side of the lane the ball goes through under the theater.
I suspect this can show up from shipping. A little grease on the shaft above the yellow circle in this picture, work it up and down a few times. and the bracket holding the blue coil in the picture, give it one gentle tug to the right in this picture ( in the game, towards the front of the playfield )
LTG : )
I previously made the changes Lloyd suggested above and mine has been great.
Quoted from LTG:Opto switch in there working ?
LTG : )
I'm testing in test mode now and around -87 seems to be working consistently in test. Going to see what happens in game play. Quick question the more negative you go does this increase the delay between when the magnet lets the ball drop and when it re-energizes?
Thanks for the quick reply Lloyd.
Is there a post that lists all of the times the theatre magnet is supposed to suck the ball back up? My magnet works in test but only seems to suck ball up on hurry up.
Quoted from frolic:watch out for the tips of those lightning bolts. I was pulling the glass and my fingers grazed them and they drew blood like a sharp knife!!
You play with lighting you get burned son
Quoted from libtech:two screws one on the left pop, one on the lower right, just have to remove the spot lamp and it pops right off!
You're currently viewing posts by Pinsider cserold.
Click here to go back to viewing the entire thread.
Wanna join the discussion? Please sign in to reply to this topic.
Great to see you're enjoying Pinside! Did you know Pinside is able to run without any 3rd-party banners or ads, thanks to the support from our visitors? Please consider a donation to Pinside and get anext to your username to show for it! Or better yet, subscribe to Pinside+!
This page was printed from https://pinside.com/pinball/forum/topic/dialed-in-owners-and-fans-club?tu=cserold and we tried optimising it for printing. Some page elements may have been deliberately hidden.
Scan the QR code on the left to jump to the URL this document was printed from.