Highgate, VT
Quoted from Phantasize:Why not a small LCD screen in the apron, hook up a PI or a Mini SNES and have it playable via a wireless controller? I believe that would be a first
Sorta did that with my T2.
Just plays the movie.
(Topic ID: 31302)
Linked Games
Demolition Man
Williams, 1994
Topic Gallery
You're currently viewing posts by Pinsider Scoot.
Click here to go back to viewing the entire thread.
4 months later
Quoted from gweempose:I'm going to guess they are coming off the yellow stand up targets, particularly the ones closest to the flippers.
Yes, mainly from the stand ups. I have replaced the foam behind them and it has helped. I still am at over 7 degrees which seems to play fine.
2 months later
Quoted from waldo34:Anyone have a lead on a Trigger button? One of mine is functional but has issues.
I have some original trigger buttons in perfect condition I will be happy to just give you, or maybe trade something for.
20191122_140225 (resized).jpgQuoted from orangegsx:Sorry I should have elaborated. The tunnel the car goes through was broken and someone fixed it with fiberglass that you can’t see through.
It does have a black car in it though, not the red one.
I would just remove it until you find a replacement. The ball may get stuck from time to time but it would look a lot better than it does now.
Quoted from Sk0r:I'm in the process of cleaning up my Demolition Man and I'm stuck with the plastic claw removal: I cannot move the claw by hand all the way behind the playfield and the 3 metal posts in front of it are preventing me from removing the plastic cover. Any idea? I didn't force the claw too much out of fear of breaking it :/
I attached some pics. I couldn't get a good look at the cryo claw board, but from what I can tell from behind the plastic, it's filled with hacks... I reached out to to GLM for a replacement one but they never replied.[quoted image][quoted image][quoted image][quoted image]
Can't you remove the three posts from under the playfield? When I removed mine, I was able to swivel the crane out of the way. Try it again or look to see if there is an obstruction somewhere. You should be able to turn it all the way.
Quoted from Sk0r:Ah good to know, thanks! Will try that tomorrow.
Also I noticed a loose wire on the cryo claw ramp. Seems to be yellow-black (or yellow-blue, not sure). Any idea where it's supposed to go?[quoted image]
It looks like it goes there.
20191128_222845 (resized).jpgI purchased a Demo Man a while back with a few issues, all of them resolved except for one. I have a locked on flasher #40 center ramp. Looking for the problem, I have checked everything thoroughly with no luck. I then focused on the Rottendog Supplemental Williams Driver Board that was powering it. I was considering replacing it, but took a close inspection of the board and found something curious. there is writing on the board that says: Demolition Man SW4 Out. Does this mean that the area SW4 should not have a resistor there? Can someone verify that this should be the case? Maybe this is the reason for my problem. I circled the area in a photo. If there is no resister there please let me know.
Scoot.
20191129_172522 (resized).jpg 1 week later
Quoted from allsportdvd:The corresponding transistors Q83, how on earth do you find the part number?
The transistor type is printed on it, so you could look them up online to find where to get one.
2 months later
Quoted from Sk0r:Thanks for the extra information. I tested again, holding both trigger buttons doesn’t change anything, still doesn’t work. I can drop on Simon Chase but any other claw position is acting up whether I use one trigger button, both trigger buttons simultaneously or just the cabinet Ball Launch button (which otherwise works fine). I read A LOT of threads about the claw but can’t remember seeing anything similar :/
I will go out on a limb and say your balls are magnetized. I switched to carbon balls and my same issue went away. I realized this when I would smack the cabinet and the ball would fall.
3 months later
Promoted items from Pinside Marketplace and Pinside Shops!
You're currently viewing posts by Pinsider Scoot.
Click here to go back to viewing the entire thread.
Reply
Wanna join the discussion? Please sign in to reply to this topic.
Hey there! Welcome to Pinside!
Donate to PinsideGreat to see you're enjoying Pinside! Did you know Pinside is able to run without any 3rd-party banners or ads, thanks to the support from our visitors? Please consider a donation to Pinside and get anext to your username to show for it! Or better yet, subscribe to Pinside+!
