(Topic ID: 253042)

Dead System 80 diagnostics, a haunting we will go.


By gdonovan

67 days ago



Topic Stats

  • 67 posts
  • 10 Pinsiders participating
  • Latest reply 37 days ago by gdonovan
  • Topic is favorited by 3 Pinsiders

You

Linked Games

Topic Gallery

There have been 32 images uploaded to this topic. (View topic image gallery).

20191105_191216_resized (resized).jpg
20191104_174520_resized (resized).jpg
20191104_182118_resized (resized).jpg
20191102_201039_resized (resized).jpg
20191102_131954_resized (resized).jpg
20191102_122440_resized (resized).jpg
20191102_122321_resized (resized).jpg
HH_scans (resized).jpg
20191101_184047 (resized).jpg
20191030_183620 (resized).jpg
20191030_183554 (resized).jpg
20191030_183438 (resized).jpg
20191030_162543_resized (resized).jpg
20191030_162019_resized (resized).jpg
20191030_150122_resized (resized).jpg
20191030_162616_resized (resized).jpg

You're currently viewing posts by Pinsider skidave.
Click here to go back to viewing the entire thread.

#11 60 days ago

I just repaired a Bally MPU with major battery damage. U8 had zero pads remaining. I had to jumper quite a bit on the backside (solder side), but it is repaired. I make all my jumpers neat and laid out as organized as possible. The battery acid also dropped on to the lamp driver below. Oh joy. The lamp driver is repaired too.

You can do it. Take your time and double check traces / vias and ohm things out as you go along and when you think you are finished.

#17 58 days ago
Quoted from gdonovan:

1) Picked up Zep tonight, that stuff works great!
2) Pulled the big solder gun out, low watt iron was just not cutting it. Much better!
Have about 10 more pieces to remove, going slow. Parts not here till Thursday. Once the last of the parts are off I'll acid wash again, clean, flux and tin the clean surfaces.

Yes, I had to pull out my higher wattage iron as well on my repair. I have a flux pen I use surface mount components. I used all over my board. Then I had to use a ton if acetone for cleaning.

Looks good.

#22 57 days ago

Looks good. I have a friend that has a Haunted House that has been used in years. He wants me to come over this winter and get it running. This is good inspiration.

1 week later
#33 45 days ago

Looking good. More photos please!

#44 43 days ago

Looks great. I'm waiting for my friend to clean up his basement so I can work on his Haunted House. I'm sure I'll have lots of questions since I'm mainly a Bally guy

#66 38 days ago

Nice. I reprint my Bally cards at home on our laser printer using thick stock paper. Nothing like a set of fresh looking instructions to finish off a game!

Promoted items from the Pinside Marketplace
€ 8.40
Wanted
Machine - Wanted
Brownsburg, IN
$ 1,099.00
Flipper Parts
Mircoplayfields
Wanted
Machine - Wanted
Shingletown, CA
From: $ 18.00
Apparel - Men
Pinside Shop
$ 159.95
Lighting - Led
Pin Stadium Pinball LEDs
2,500
Machine - For Sale
San Diego, CA
From: $ 20.00
Cabinet - Other
Rock Custom Pinball
Wanted
Machine - Wanted
Bristol, TN
$ 279.95
Cabinet - Toppers
COINTAKER.COM
$ 339.00
From: $ 20.00
Cabinet - Other
Rock Custom Pinball

You're currently viewing posts by Pinsider skidave.
Click here to go back to viewing the entire thread.

Hey there! Got a moment?

Great to see you're enjoying Pinside! Did you know Pinside is able to run thanks to donations from our visitors? Please donate to Pinside, support the site and get anext to your username to show for it! Donate to Pinside