Black Knight
Williams, 1980
Black Knight Limited Edition
Williams, 1981You're currently viewing posts by Pinsider boydsc331.
Click here to go back to viewing the entire thread.
Quoted from Toyguy:Anyone have a photo of what I assume must have been a serial number label on the back of the lower cabinet? Mine has gone completely white and I'd like to try recreating one. Thanks!
not sure if this is what your looking for but its the only sticker on the back of my lower cabinet.
20140805_225247[1].jpg
20140805_225108[1].jpg
Quoted from Silverballer:That is one nice BK Blazed!
hey silverballer is there really a town named pinville in MO. ? lol
Quoted from SilverUnicorn:Methinks I have a Power Supply problem
Here is a craptastic one handed cell phone video. When I hit both flippers, the machine resets. Sometimes right away, or, as in this vodeo, after a few flips.
Can someone confirm a power supply issue? It is the original PS board, but the caps were redone a while back.
Any other ideas if not the PS?
» YouTube video
Thanks
Chris
hey chris I had that same exact problem on my bk. the power supply was rebuilt with new caps and diodes according to vids guide for bulletproofing sys 3-7 and I had a new rotterndog mpu installed. anyway it turned out to be the slam tilt switch in the coin door. even tho it wasn't touching it would still reset when I would push the flippers once or twice. I disconnected it completely and have not hAD the problem since. my machine was in a pizza place or a bar before I got it because it smelled like beer and sticky like coke inside the coin door. so maybe the switch was too dirty where the wires connected I don't know . not sure if this helps but thought i'd throw it out there.
Quoted from Boise_D:Can anyone check the rubber route and size just to the right of the upper left flipper? The ring guide says this should 2", but that is too big, even If I loop the third post in.
image.jpg 227 KB
heres the diagram I used it seemed to work for me
img011.jpg
Quoted from Toyguy:Those diagrams are either incorrect or there were some mid-stream design changes. My BK looks like Boise's.
The printed diagram calls out C as 1.25" which seems about right, although its placement is not as represented in the drawing. As you can see, it does not extend to the flipper pivot. Note too that you do want a ring around that post at the left side of the gate. You can just see it in the photo.
DaveDSCN0978.JPG 142 KB
yes you are right now that I look at the diagram closer. I did use the 1 1/2 " ring like it says, but it does not look like the diagram. mine looks like your guys's
20141102_222910.jpg
Quoted from Boise_D:Now compare the diagram for the other flipper up there.
ya the chart has the right sizes but the picture is wrong..................................... so whos gonna get out the photoshop and fix it ??? 
Quoted from Boise_D:I had 4.8 on there before I tore it apart. Accidentally hit the reset.
pictures or it didn't happen .lol
or maybe check the resistance to see where your at. http://www.flippers.com/coil-resistance.html
You're currently viewing posts by Pinsider boydsc331.
Click here to go back to viewing the entire thread.
Wanna join the discussion? Please sign in to reply to this topic.
Great to see you're enjoying Pinside! Did you know Pinside is able to run without any 3rd-party banners or ads, thanks to the support from our visitors? Please consider a donation to Pinside and get anext to your username to show for it! Or better yet, subscribe to Pinside+!
This page was printed from https://pinside.com/pinball/forum/topic/black-knight-clubmembers-only?tu=boydsc331 and we tried optimising it for printing. Some page elements may have been deliberately hidden.
Scan the QR code on the left to jump to the URL this document was printed from.
Lake Forest, CA