Atlantis
Bally, 1989You're currently viewing posts by Pinsider Timerider.
Click here to go back to viewing the entire thread.
Quoted from Pinballer22:Might pull mylar as well...has anyone done it on this title? Good/bad results??
When I pulled my Mylar, I lost about 3-4 inserts artwork. (just numbers/words...so not too horrified)
It was getting the rest of the glue up that took forever. (lots of Goo Gone, papertowels & raw, sore fingers)
(I had long, high air bubbled Mylar running across the playfield in multiple places that required it be pulled.)
Just an FYI... if your Atlantis sub is in need of a ball gate (A-12554 or A-12765 depending on if you're looking at the manual or the Bally Parts catalog)... I found a perfect substitute.
Part number: A-14788
In stock at BAA. http://bayareaamusements.com/Merchant2/merchant.mvc?Screen=PROD&Product_Code=GS-HURA-14788
Mine was missing the spring-steel and I tried to cut & mount my own from a piece of ramp flap, but could never quite get it right. (and ended up with balls prematurely ejecting) 
I've had this one installed for a bit now, and no balls falling out of the ship before ejecting, etc. Works great.
Here's my old one, with a rigged spring-metal, and the NOS I got from BAA.
ball_gate1.jpgQuoted from danczaz:Ok shape... Super dirty on inside kind of like some photos in here... I cleaned a lot of the dirtiness off in this photo..,got to figure out about that duct tape on ramp...
Nice!
The mylar looks flat in the picture... should clean up nice.
Your side-rails look like mine did. Guessing your chrome head trim is crushed & speaker grill dented too.
I found an extremely close match for the chrome at AutoZone (or similar place).
No one makes the correct length side-rails at this time.
Quoted from Tsskinne:So balls keep falling out of sub when I hit ramp hard, any tips?
Make sure the gate is in there and the spring metal is there... see this post:
https://pinside.com/pinball/forum/topic/bally-atlantis-ownerss-club-fans-welcome/page/2#post-1621549
Quoted from Tsskinne:Ok so I'm a moron, spring steel there. Adjusted it and playing great now with the exception of that White GI. Hopefully get that relay board fixed in a few days.
Glad you got the sub launching correctly... sorry the link was busted (I didn't re-check it). I'm guessing they must have sold out.
Quoted from tbmi:I am looking for the L3 Roms for Atlantis. According to John Wart's website, he doesn't currently offer this era of Bally Roms. Anyone else have them that I can purchase?
Action Pinball sells them...
http://www.actionpinball.com/parts.php?item=ROMS16
Or maybe give your general location and someone local can help you out.
Quoted from billsgto:Would anyone happen to have the schematics for the relay board they could share? It's not in my manual, the part I see is 5768-12390-00.
Thank you
You might check this thread... seems to have similar issue, and has some of the relay wiring/pinouts listed within the thread.
https://pinside.com/pinball/forum/topic/bally-atlantisneed-a-little-help-please
Quoted from KentCO:Yeah there is a gap right there. So do you have a hole right next to your bumper like I do or am I missing one?
Not unless your bracket post is going thru the wrong hole.
Here's what mine looks like. (the 2 forward holes are the sub mounts to the playfield)
Atl_sub1 (resized).jpgQuoted from KentCO:Also what shape is your little whisker switch in? Mine looks like it’s been bent to hell. It looks like a man made hole as well. Thank you so much for your help. I’m completely lost with the multiball
[quoted image]
Your gate/bracket is correct. My spring-steel was busted, so I had rigged with a screw, until I found a new gate. (now out of stock everywhere)
https://pinside.com/pinball/forum/topic/bally-atlantis-ownerss-club-fans-welcome/page/2#post-1621549
However, your coil sleeve looks wrong. Should be more like this one: https://www.pinballlife.com/index.php?p=product&id=2900
My switch wire was in good shape. (picture pre-rebuild)
Atl_sw1 (resized).jpgQuoted from djsolzs:My gate coil solenoid was blown out so I order a new GA-34-4000 Gate Coil Solenoid based on what was in there previously. The previous one had a diode the one I ordered does not.
Any help me out here? Does yours have diode? Thanks[quoted image]
For the ramp lock solenoid? No, a 34-4000 is the wrong coil.
Per the manual, its a SM-28-900, and yes, with a diode. (and that is what is in mine)
https://www.marcospecialties.com/pinball-parts/SM-28-900
coil (resized).pngYou're currently viewing posts by Pinsider Timerider.
Click here to go back to viewing the entire thread.
Wanna join the discussion? Please sign in to reply to this topic.
Great to see you're enjoying Pinside! Did you know Pinside is able to run without any 3rd-party banners or ads, thanks to the support from our visitors? Please consider a donation to Pinside and get anext to your username to show for it! Or better yet, subscribe to Pinside+!
This page was printed from https://pinside.com/pinball/forum/topic/bally-atlantis-ownerss-club-fans-welcome?tu=Timerider and we tried optimising it for printing. Some page elements may have been deliberately hidden.
Scan the QR code on the left to jump to the URL this document was printed from.
Trevor, WI