Hi AdreXis,
you can get some at free-play.se
You're currently viewing posts by Pinsider pinballoo.
Click here to go back to viewing the entire thread.
Hi there,
yesterday the airlock-display started flickering and then completely went off.
Now the game won´t start and the message "IO board 1 missing" appears.
I´ve changed the IO board but with no effect.....(guessed No.1 is the one located in the top of the playfield?? )
Any ideas?
Quoted from TomDK:Shoot me a PM with your email adress ....
Thanks, Averell just helped me out
Hi there,
Sometimes the Xeno-tongue gets stuck at the moment when grabbing the ball...this came after updating
the game code from v.1.2 to 1.4
Any suggestions except reinstalling 1.2?
Thanks in advance!
Hi there ,
my xeno´s jaw doesn´t move anymore. It worked before a little "weak"
and now it´s dead...seems like cables are okay so far.
Any ideas?
Quoted from fuko:I'll be very interested to see what parts from the new PB Alien could be used to repair/upgrade a HW Alien.
Plastics for sure. That's great news.
Facehuggers with a broken tail, maybe?
PCB and anything else: probably a long shot.
I mailed with PB asking the same question and they said:
"We don´t think so"
What an answer...
Quoted from Ferret:That’s likely the only correct answer. If you just compare the underside of the Heighway Alien vs the Pinball Bros Alien, it’s clear that there is little in common between the builds.
Okay, thanks ferret...I never seen any technical details of the new machine
Quoted from Averell:Check the small driver circuit behind the panel in the back of the playfield.
Often it's toasted... you can order this thing on Ebay.
[quoted image]
It doesn´t look toasted...maybe still a cable issue?
IMG_3107[1] (resized).JPGQuoted from MK6PIN:Any noise when in test mode? If you can hear ( slightly) something but jaw not moving it could be the stepper motor gears are stripped ( early ones were plastic) strong, cheap metal geared versions available...just a thought..
Thanks, new metal geared Stepper motor was installed weeks ago..can´t be the problem
Quoted from Averell:Replace the small circuit board in the socket.
I already had two of them broken.
Order here: ebay.com link: itm
A4988 Stepper Motor Drive
Thanks Averell for the link, that should make it.
The micro switches of both Xeno-targets break regularly...
Does anyone have a solution for this problem?
Thanks!
Quoted from TomDK:Xenotargets = Standuptargets ??!!
Dont Understand.
Exactly! The two under the xeno jaw
Quoted from Mik-ReadingUK:Gameroom.no still have the switch boards so hopefully I can reuse the target shell with them. I'll post the result when they eventually turn up.
I´ve swapped the switch boards or just the switches several times...I´m bored of it.
Hopefully the redesign by PB is more reliable and fits in the old Heighways?
Hi there,
Not for the first time a Mosfet on the IO-board smokes off. What could be the reasons for this?I have already adjusted the coil force, but now it has happened again.
Thanks in advance
Hi there,
Not for the first time a Mosfet on the IO-board smokes off. What could be the reasons for this? I have already adjusted the coil force, but now it has happened again..
Thanks in advance
Quoted from chucky87:your mosfet smoked straight away? if yes, it may be too much voltage passing through, it may be a problem upstream
Not straight away, during Gameplay.
Quoted from MK6PIN:What version of boards? What software?
Same board, same failure point? Upstream might be the correct path to check....board just taking the brunt of what's going on...
board v. 1.4B, software 1.4
i´m no professional, where should i check "upstream"?
Quoted from chucky87:Hi everyone here is my 1st backglass lighting test like the lighting of the blades and the backboard. Small modifications must still be made but already this changes everything and gives all its splendor to the backglass. It's up to you to make up your mind with the images.
[quoted image][quoted image][quoted image][quoted image][quoted image][quoted image][quoted image]
Fantastic! I´m in for one if it´s not too pricey
You're currently viewing posts by Pinsider pinballoo.
Click here to go back to viewing the entire thread.
Wanna join the discussion? Please sign in to reply to this topic.
Great to see you're enjoying Pinside! Did you know Pinside is able to run without any 3rd-party banners or ads, thanks to the support from our visitors? Please consider a donation to Pinside and get anext to your username to show for it! Or better yet, subscribe to Pinside+!
This page was printed from https://pinside.com/pinball/forum/topic/alien-pinball-official-game-thread?tu=pinballoo and we tried optimising it for printing. Some page elements may have been deliberately hidden.
Scan the QR code on the left to jump to the URL this document was printed from.