(Topic ID: 94048)

Addams Family Pop Bumpers and slings not working, Help!

By thadawkins

9 years ago


Topic Heartbeat

Topic Stats

You

Linked Games

You're currently viewing posts by Pinsider thadawkins.
Click here to go back to viewing the entire thread.

#1 9 years ago

So i had issues with the Thing Flips optos not working so i took out the transmitter and disconnected the harness under the playfield. Now my Pop Bumpers and Slings don't work. I have checked for loose wires and there are none. Went through the solenoid test and all the solenoids fire but the switches are not registering for any of them. Checked all the fuses and everything is good. Kind of stumped at this point and at a stand still. Any help would be awesome. Thanks

#3 9 years ago

i removed the harness for the opto transmitter under the playfield

#5 9 years ago

No it doesnt

#6 9 years ago

it seems to me that the switches are not working. None of them activate when i press them in the switch test

#11 9 years ago

i have followed the green/orange to all of the switches in that matrix diagram and can't find broken wires. I am assuming that it would be right at the beginning if all of them are out right?

#12 9 years ago

I am getting 12v on the first upper left loop switch but after that none of the switches have power

#15 9 years ago

i get continuity from switch to switch

#17 9 years ago

So you are saying to check continuity from the white wire to white wire? I do not have continuity with the white wires, only the green ones

Super exclusive ad from the Pinside Marketplace!
#18 9 years ago

Do the switches have to be "closed" for continuity to happen between the white wires?

#20 9 years ago

i get continuity from the back box to the first switch for both green/orange and white wires. The switch doesnt register in test mode though, that confuses me

#22 9 years ago

Yes I do

#24 9 years ago

I looked at the fuses and didn't find any blown ones. I will test them in a min

#27 9 years ago

The upper left loop switch doesn't register in test mode. Must be a board issue from what I've been reading

#31 9 years ago

It was a board issue. I ended up buying a new MPU which wasn't that much. I am sure it was the U14 MPU which was the only one not replaced. I am sending the board in for repair. Thanks for the help!

#32 9 years ago

Now I am having an issue with the lower opto in the Thing Hand not registering.

#35 9 years ago

Thanks Schnob. I tested and got continuity from the wiring in the backbox and the wiring that goes to the opto board for both lines on the switch matrix. I just ordered the whole opto board for $30.

Promoted items from the Pinside Marketplace
$ 38.00
Various Novelties
Pinball Photos LLC
Various novelties
$ 49.99
$ 35.00
Various Other Swag
JK Pinball
Various other swag
$ 54.99
Cabinet - Shooter Rods
Lighted Pinball Mods
Shooter rods
$ 53.99
Eproms
Matt's Basement Arcade
Eproms
$ 299.95
Lighting - Led
Pin Stadium Pinball Mods
Led
$ 399.00
Cabinet - Decals
Mircoplayfields
Decals
16,500 (OBO)
$ 140.00
Playfield - Toys/Add-ons
pinballmod
Toys/Add-ons
$ 84.99
Playfield - Toys/Add-ons
GMods
Toys/Add-ons
$ 1,059.00
Flipper Parts
Mircoplayfields
Flipper parts
$ 39.00
Cabinet - Other
Arcade Upkeep
Other
From: $ 11.95
Playfield - Toys/Add-ons
ULEKstore
Toys/Add-ons
$ 44.99
Cabinet - Shooter Rods
Pinball Shark
Shooter rods
11,500 (OBO)
Machine - For Sale
Hanford, CA
10,500 (OBO)
Machine - For Sale
Roselle, IL
$ 109.95
Electronics
PinSound
Electronics
$ 219.00
Gameroom - Decorations
Lit Frames
Decorations
$ 29.00
Cabinet - Other
Filament Printing
Other
$ 25.99
Lighting - Led
Lee's Parts
Led
$ 54.99
Cabinet - Shooter Rods
Lighted Pinball Mods
Shooter rods
$ 65.00
Cabinet - Armor And Blades
arcade-cabinets.com
Armor and blades
From: $ 8.00
Playfield - Toys/Add-ons
Twisted Tokens
Toys/Add-ons
Wanted
Machine - Wanted
Pensacola, FL
$ 79.00
Lighting - Under Cabinet
Arcade Upkeep
Under cabinet
$ 145.00
Playfield - Toys/Add-ons
Twisted Tokens
Toys/Add-ons
From: $ 15.00
Cabinet - Other
NO GOUGE PINBALL™
Other
$ 1,159.00
Flipper Parts
Mircoplayfields
Flipper parts
$ 180.00
Cabinet Parts
Starcade Amusement
Cabinet parts
$ 8.50
Lighting - Led
Pinball Haus
Led
Hey modders!
Your shop name here

You're currently viewing posts by Pinsider thadawkins.
Click here to go back to viewing the entire thread.

Reply

Wanna join the discussion? Please sign in to reply to this topic.

Hey there! Welcome to Pinside!

Donate to Pinside

Great to see you're enjoying Pinside! Did you know Pinside is able to run without any 3rd-party banners or ads, thanks to the support from our visitors? Please consider a donation to Pinside and get anext to your username to show for it! Or better yet, subscribe to Pinside+!


This page was printed from https://pinside.com/pinball/forum/topic/addams-family-pop-bumpers-and-slings-not-working-help?tu=thadawkins and we tried optimising it for printing. Some page elements may have been deliberately hidden.

Scan the QR code on the left to jump to the URL this document was printed from.