(Topic ID: 167361)

77 Gottlieb jungle princess quits abruptly during play


By DirtinLa

3 years ago



Topic Stats

  • 26 posts
  • 6 Pinsiders participating
  • Latest reply 3 years ago by DirtinLa
  • Topic is favorited by 1 Pinsider

You

Linked Games

Topic Gallery

There have been 14 images uploaded to this topic. (View topic image gallery).

IMG_5717 (resized).JPG
IMG_5721 (resized).JPG
IMG_5713[1] (resized).JPG
IMG_5715[1] (resized).JPG
IMG_5716[1] (resized).JPG
IMG_5711[1] (resized).JPG
IMG_5708[1] (resized).JPG
IMG_5707[1] (resized).JPG
IMG_5708[1] (resized).JPG
IMG_5698[1] (resized).JPG
IMG_5697[1] (resized).JPG
IMG_5693[1] (resized).JPG
IMG_5692[1] (resized).JPG
IMG_5691[1] (resized).JPG

You're currently viewing posts by Pinsider timme.
Click here to go back to viewing the entire thread.

#2 3 years ago

Try cleaning and adjusting the switches on the game over relay. You'll want to tighten down the switch stack screws before adjusting the switches, and also check to be sure no wires have gotten detached at the solder lugs of the switches.

- TimMe

#9 3 years ago

Did you check the switches on the tilt-hold relay, too? Other than the switches on the game over relay and the tilt-hold relay, there isn't much in the normal circuit control path that can kill the PF power, yet leave the rest of the game working - lights on, no tilt, etc.

Are the PF switches still scoring points when the flippers and pop bumpers go dead? If so, I would start checking the coil black return wire that is daisy-chained to all the coils under the PF. It may be that you have a bad solder joint or broken wire at one of the coils early in the daisy-chain of this wiring. That would knock out power to all the PF coils downstream from the fault, but leave everything else in the game working. Be sure to check the relay coils on the underside of the PF as well as the solenoid coils.

Similarly, if the coil black return wire connection on the jones plug between the PF and bottom board is failing, you will get this same symptom. So you might want to carefully examine the jones plug sockets for the PF and see if you've got a broken wire or fractured socket clip.

- TimMe

#12 3 years ago

Regarding post #10, that's a lamp (6 VAC) power supply wire. It probably broke off of the solder lug attached to the frame of the bonus stepper unit. If so, that wire supplies power to the bonus ladder lights through the frame-grounded wiper on the bonus stepper.

In any event, having a lamp wire loose would not cause the game to stop working in the middle of a game.

- TimMe

Promoted items from the Pinside Marketplace
$ 84.95
Cabinet - Shooter Rods
Super Skill Shot Shop
From: $ 18.00
Apparel - Men
Pinside Shop
$ 6.00
Electronics
German-Pinball-Modular
$ 69.99
Playfield - Toys/Add-ons
Lighted Pinball Mods
From: $ 42.00
Cabinet - Shooter Rods
ModFather Pinball Mods
$ 9.95
Playfield - Toys/Add-ons
pinballmod
$ 14.95
Playfield - Toys/Add-ons
ULEKstore
$ 369.00
Cabinet - Decals
Mircoplayfields
$ 18.95
$ 999.00
Flipper Parts
Mircoplayfields
$ 74.00
Cabinet - Armor And Blades
Id Rather Play Pinball
$ 8.00
Cabinet Parts
Pinball Haus
$ 20.00
Playfield - Decals
Flashinstinct
From: $ 220.00
Playfield - Toys/Add-ons
CzTV Mods
From: $ 19.99
$ 69.00
Playfield - Protection
The MOD Couple
$ 9.99
Eproms
Matt's Basement Arcade
$ 15.75
Cabinet Parts
Tilted Pinball
$ 60.00
$ 29.95
Playfield - Toys/Add-ons
ULEKstore
$ 45.00
Playfield - Toys/Add-ons
The MOD Couple
$ 137.00

You're currently viewing posts by Pinsider timme.
Click here to go back to viewing the entire thread.

Hey there! Got a moment?

Great to see you're enjoying Pinside! Did you know Pinside is able to run thanks to donations from our visitors? Please donate to Pinside, support the site and get anext to your username to show for it! Donate to Pinside